/* Data Path Network Interface API * Contains initialization APIs and runtime control APIs for DPNI
*/
/** General DPNI macros */
/** * DPNI_MAX_TC - Maximum number of traffic classes
*/ #define DPNI_MAX_TC 8 /** * DPNI_MAX_DPBP - Maximum number of buffer pools per DPNI
*/ #define DPNI_MAX_DPBP 8
/** * DPNI_ALL_TCS - All traffic classes considered; see dpni_set_queue()
*/ #define DPNI_ALL_TCS (u8)(-1) /** * DPNI_ALL_TC_FLOWS - All flows within traffic class considered; see * dpni_set_queue()
*/ #define DPNI_ALL_TC_FLOWS (u16)(-1) /** * DPNI_NEW_FLOW_ID - Generate new flow ID; see dpni_set_queue()
*/ #define DPNI_NEW_FLOW_ID (u16)(-1)
/** * DPNI_OPT_TX_FRM_RELEASE - Tx traffic is always released to a buffer pool on * transmit, there are no resources allocated to have the frames confirmed back * to the source after transmission.
*/ #define DPNI_OPT_TX_FRM_RELEASE 0x000001 /** * DPNI_OPT_NO_MAC_FILTER - Disables support for MAC address filtering for * addresses other than primary MAC address. This affects both unicast and * multicast. Promiscuous mode can still be enabled/disabled for both unicast * and multicast. If promiscuous mode is disabled, only traffic matching the * primary MAC address will be accepted.
*/ #define DPNI_OPT_NO_MAC_FILTER 0x000002 /** * DPNI_OPT_HAS_POLICING - Allocate policers for this DPNI. They can be used to * rate-limit traffic per traffic class (TC) basis.
*/ #define DPNI_OPT_HAS_POLICING 0x000004 /** * DPNI_OPT_SHARED_CONGESTION - Congestion can be managed in several ways, * allowing the buffer pool to deplete on ingress, taildrop on each queue or * use congestion groups for sets of queues. If set, it configures a single * congestion groups across all TCs. If reset, a congestion group is allocated * for each TC. Only relevant if the DPNI has multiple traffic classes.
*/ #define DPNI_OPT_SHARED_CONGESTION 0x000008 /** * DPNI_OPT_HAS_KEY_MASKING - Enables TCAM for Flow Steering and QoS look-ups. * If not specified, all look-ups are exact match. Note that TCAM is not * available on LS1088 and its variants. Setting this bit on these SoCs will * trigger an error.
*/ #define DPNI_OPT_HAS_KEY_MASKING 0x000010 /** * DPNI_OPT_NO_FS - Disables the flow steering table.
*/ #define DPNI_OPT_NO_FS 0x000020 /** * DPNI_OPT_SHARED_FS - Flow steering table is shared between all traffic * classes
*/ #define DPNI_OPT_SHARED_FS 0x001000
int dpni_open(struct fsl_mc_io *mc_io,
u32 cmd_flags, int dpni_id,
u16 *token);
int dpni_close(struct fsl_mc_io *mc_io,
u32 cmd_flags,
u16 token);
/** * struct dpni_pools_cfg - Structure representing buffer pools configuration * @num_dpbp: Number of DPBPs * @pool_options: Buffer assignment options. * This field is a combination of DPNI_POOL_ASSOC_flags * @pools: Array of buffer pools parameters; The number of valid entries * must match 'num_dpbp' value * @pools.dpbp_id: DPBP object ID * @pools.priority: Priority mask that indicates TC's used with this buffer. * If set to 0x00 MC will assume value 0xff. * @pools.buffer_size: Buffer size * @pools.backup_pool: Backup pool
*/ struct dpni_pools_cfg {
u8 num_dpbp;
u8 pool_options; struct { int dpbp_id;
u8 priority_mask;
u16 buffer_size; int backup_pool;
} pools[DPNI_MAX_DPBP];
};
/** * struct dpni_attr - Structure representing DPNI attributes * @options: Any combination of the following options: * DPNI_OPT_TX_FRM_RELEASE * DPNI_OPT_NO_MAC_FILTER * DPNI_OPT_HAS_POLICING * DPNI_OPT_SHARED_CONGESTION * DPNI_OPT_HAS_KEY_MASKING * DPNI_OPT_NO_FS * @num_queues: Number of Tx and Rx queues used for traffic distribution. * @num_tcs: Number of traffic classes (TCs), reserved for the DPNI. * @mac_filter_entries: Number of entries in the MAC address filtering table. * @vlan_filter_entries: Number of entries in the VLAN address filtering table. * @qos_entries: Number of entries in the QoS classification table. * @fs_entries: Number of entries in the flow steering table. * @qos_key_size: Size, in bytes, of the QoS look-up key. Defining a key larger * than this when adding QoS entries will result in an error. * @fs_key_size: Size, in bytes, of the flow steering look-up key. Defining a * key larger than this when composing the hash + FS key will * result in an error. * @wriop_version: Version of WRIOP HW block. The 3 version values are stored * on 6, 5, 5 bits respectively.
*/ struct dpni_attr {
u32 options;
u8 num_queues;
u8 num_tcs;
u8 mac_filter_entries;
u8 vlan_filter_entries;
u8 qos_entries;
u16 fs_entries;
u8 qos_key_size;
u8 fs_key_size;
u16 wriop_version;
};
/** * enum dpni_error_action - Defines DPNI behavior for errors * @DPNI_ERROR_ACTION_DISCARD: Discard the frame * @DPNI_ERROR_ACTION_CONTINUE: Continue with the normal flow * @DPNI_ERROR_ACTION_SEND_TO_ERROR_QUEUE: Send the frame to the error queue
*/ enum dpni_error_action {
DPNI_ERROR_ACTION_DISCARD = 0,
DPNI_ERROR_ACTION_CONTINUE = 1,
DPNI_ERROR_ACTION_SEND_TO_ERROR_QUEUE = 2
};
/** * struct dpni_error_cfg - Structure representing DPNI errors treatment * @errors: Errors mask; use 'DPNI_ERROR__<X> * @error_action: The desired action for the errors mask * @set_frame_annotation: Set to '1' to mark the errors in frame annotation * status (FAS); relevant only for the non-discard action
*/ struct dpni_error_cfg {
u32 errors; enum dpni_error_action error_action; int set_frame_annotation;
};
/** * DPNI_BUF_LAYOUT_OPT_TIMESTAMP - Select to modify the time-stamp setting
*/ #define DPNI_BUF_LAYOUT_OPT_TIMESTAMP 0x00000001 /** * DPNI_BUF_LAYOUT_OPT_PARSER_RESULT - Select to modify the parser-result * setting; not applicable for Tx
*/ #define DPNI_BUF_LAYOUT_OPT_PARSER_RESULT 0x00000002 /** * DPNI_BUF_LAYOUT_OPT_FRAME_STATUS - Select to modify the frame-status setting
*/ #define DPNI_BUF_LAYOUT_OPT_FRAME_STATUS 0x00000004 /** * DPNI_BUF_LAYOUT_OPT_PRIVATE_DATA_SIZE - Select to modify the private-data-size setting
*/ #define DPNI_BUF_LAYOUT_OPT_PRIVATE_DATA_SIZE 0x00000008 /** * DPNI_BUF_LAYOUT_OPT_DATA_ALIGN - Select to modify the data-alignment setting
*/ #define DPNI_BUF_LAYOUT_OPT_DATA_ALIGN 0x00000010 /** * DPNI_BUF_LAYOUT_OPT_DATA_HEAD_ROOM - Select to modify the data-head-room setting
*/ #define DPNI_BUF_LAYOUT_OPT_DATA_HEAD_ROOM 0x00000020 /** * DPNI_BUF_LAYOUT_OPT_DATA_TAIL_ROOM - Select to modify the data-tail-room setting
*/ #define DPNI_BUF_LAYOUT_OPT_DATA_TAIL_ROOM 0x00000040
/** * struct dpni_buffer_layout - Structure representing DPNI buffer layout * @options: Flags representing the suggested modifications to the buffer * layout; Use any combination of 'DPNI_BUF_LAYOUT_OPT_<X>' flags * @pass_timestamp: Pass timestamp value * @pass_parser_result: Pass parser results * @pass_frame_status: Pass frame status * @private_data_size: Size kept for private data (in bytes) * @data_align: Data alignment * @data_head_room: Data head room * @data_tail_room: Data tail room
*/ struct dpni_buffer_layout {
u32 options; int pass_timestamp; int pass_parser_result; int pass_frame_status;
u16 private_data_size;
u16 data_align;
u16 data_head_room;
u16 data_tail_room;
};
/** * enum dpni_queue_type - Identifies a type of queue targeted by the command * @DPNI_QUEUE_RX: Rx queue * @DPNI_QUEUE_TX: Tx queue * @DPNI_QUEUE_TX_CONFIRM: Tx confirmation queue * @DPNI_QUEUE_RX_ERR: Rx error queue
*/ enum dpni_queue_type {
DPNI_QUEUE_RX,
DPNI_QUEUE_TX,
DPNI_QUEUE_TX_CONFIRM,
DPNI_QUEUE_RX_ERR,
};
/** * struct dpni_link_state - Structure representing DPNI link state * @rate: Rate * @options: Mask of available options; use 'DPNI_LINK_OPT_<X>' values * @up: Link state; '0' for down, '1' for up
*/ struct dpni_link_state {
u32 rate;
u64 options; int up;
};
int dpni_clear_mac_filters(struct fsl_mc_io *mc_io,
u32 cmd_flags,
u16 token, int unicast, int multicast);
/** * enum dpni_dist_mode - DPNI distribution mode * @DPNI_DIST_MODE_NONE: No distribution * @DPNI_DIST_MODE_HASH: Use hash distribution; only relevant if * the 'DPNI_OPT_DIST_HASH' option was set at DPNI creation * @DPNI_DIST_MODE_FS: Use explicit flow steering; only relevant if * the 'DPNI_OPT_DIST_FS' option was set at DPNI creation
*/ enum dpni_dist_mode {
DPNI_DIST_MODE_NONE = 0,
DPNI_DIST_MODE_HASH = 1,
DPNI_DIST_MODE_FS = 2
};
/** * enum dpni_fs_miss_action - DPNI Flow Steering miss action * @DPNI_FS_MISS_DROP: In case of no-match, drop the frame * @DPNI_FS_MISS_EXPLICIT_FLOWID: In case of no-match, use explicit flow-id * @DPNI_FS_MISS_HASH: In case of no-match, distribute using hash
*/ enum dpni_fs_miss_action {
DPNI_FS_MISS_DROP = 0,
DPNI_FS_MISS_EXPLICIT_FLOWID = 1,
DPNI_FS_MISS_HASH = 2
};
int dpni_prepare_key_cfg(conststruct dpkg_profile_cfg *cfg,
u8 *key_cfg_buf);
/** * struct dpni_rx_tc_dist_cfg - Rx traffic class distribution configuration * @dist_size: Set the distribution size; * supported values: 1,2,3,4,6,7,8,12,14,16,24,28,32,48,56,64,96, * 112,128,192,224,256,384,448,512,768,896,1024 * @dist_mode: Distribution mode * @key_cfg_iova: I/O virtual address of 256 bytes DMA-able memory filled with * the extractions to be used for the distribution key by calling * dpni_prepare_key_cfg() relevant only when * 'dist_mode != DPNI_DIST_MODE_NONE', otherwise it can be '0' * @fs_cfg: Flow Steering table configuration; only relevant if * 'dist_mode = DPNI_DIST_MODE_FS'
*/ struct dpni_rx_tc_dist_cfg {
u16 dist_size; enum dpni_dist_mode dist_mode;
u64 key_cfg_iova; struct dpni_fs_tbl_cfg fs_cfg;
};
/** * DPNI_FS_MISS_DROP - When used for fs_miss_flow_id in function * dpni_set_rx_dist, will signal to dpni to drop all unclassified frames
*/ #define DPNI_FS_MISS_DROP ((uint16_t)-1)
/** * struct dpni_rx_dist_cfg - Rx distribution configuration * @dist_size: distribution size * @key_cfg_iova: I/O virtual address of 256 bytes DMA-able memory filled with * the extractions to be used for the distribution key by calling * dpni_prepare_key_cfg(); relevant only when enable!=0 otherwise * it can be '0' * @enable: enable/disable the distribution. * @tc: TC id for which distribution is set * @fs_miss_flow_id: when packet misses all rules from flow steering table and * hash is disabled it will be put into this queue id; use * DPNI_FS_MISS_DROP to drop frames. The value of this field is * used only when flow steering distribution is enabled and hash * distribution is disabled
*/ struct dpni_rx_dist_cfg {
u16 dist_size;
u64 key_cfg_iova;
u8 enable;
u8 tc;
u16 fs_miss_flow_id;
};
/** * struct dpni_qos_tbl_cfg - Structure representing QOS table configuration * @key_cfg_iova: I/O virtual address of 256 bytes DMA-able memory filled with * key extractions to be used as the QoS criteria by calling * dpkg_prepare_key_cfg() * @discard_on_miss: Set to '1' to discard frames in case of no match (miss); * '0' to use the 'default_tc' in such cases * @default_tc: Used in case of no-match and 'discard_on_miss'= 0
*/ struct dpni_qos_tbl_cfg {
u64 key_cfg_iova; int discard_on_miss;
u8 default_tc;
};
/** * enum dpni_dest - DPNI destination types * @DPNI_DEST_NONE: Unassigned destination; The queue is set in parked mode and * does not generate FQDAN notifications; user is expected to * dequeue from the queue based on polling or other user-defined * method * @DPNI_DEST_DPIO: The queue is set in schedule mode and generates FQDAN * notifications to the specified DPIO; user is expected to dequeue * from the queue only after notification is received * @DPNI_DEST_DPCON: The queue is set in schedule mode and does not generate * FQDAN notifications, but is connected to the specified DPCON * object; user is expected to dequeue from the DPCON channel
*/ enum dpni_dest {
DPNI_DEST_NONE = 0,
DPNI_DEST_DPIO = 1,
DPNI_DEST_DPCON = 2
};
/** * struct dpni_queue - Queue structure * @destination: - Destination structure * @destination.id: ID of the destination, only relevant if DEST_TYPE is > 0. * Identifies either a DPIO or a DPCON object. * Not relevant for Tx queues. * @destination.type: May be one of the following: * 0 - No destination, queue can be manually * queried, but will not push traffic or * notifications to a DPIO; * 1 - The destination is a DPIO. When traffic * becomes available in the queue a FQDAN * (FQ data available notification) will be * generated to selected DPIO; * 2 - The destination is a DPCON. The queue is * associated with a DPCON object for the * purpose of scheduling between multiple * queues. The DPCON may be independently * configured to generate notifications. * Not relevant for Tx queues. * @destination.hold_active: Hold active, maintains a queue scheduled for longer * in a DPIO during dequeue to reduce spread of traffic. * Only relevant if queues are * not affined to a single DPIO. * @user_context: User data, presented to the user along with any frames * from this queue. Not relevant for Tx queues. * @flc: FD FLow Context structure * @flc.value: Default FLC value for traffic dequeued from * this queue. Please check description of FD * structure for more information. * Note that FLC values set using dpni_add_fs_entry, * if any, take precedence over values per queue. * @flc.stash_control: Boolean, indicates whether the 6 lowest * - significant bits are used for stash control. * significant bits are used for stash control. If set, the 6 * least significant bits in value are interpreted as follows: * - bits 0-1: indicates the number of 64 byte units of context * that are stashed. FLC value is interpreted as a memory address * in this case, excluding the 6 LS bits. * - bits 2-3: indicates the number of 64 byte units of frame * annotation to be stashed. Annotation is placed at FD[ADDR]. * - bits 4-5: indicates the number of 64 byte units of frame * data to be stashed. Frame data is placed at FD[ADDR] + * FD[OFFSET]. * For more details check the Frame Descriptor section in the * hardware documentation.
*/ struct dpni_queue { struct {
u16 id; enum dpni_dest type; char hold_active;
u8 priority;
} destination;
u64 user_context; struct {
u64 value; char stash_control;
} flc;
};
/** * struct dpni_queue_id - Queue identification, used for enqueue commands * or queue control * @fqid: FQID used for enqueueing to and/or configuration of this specific FQ * @qdbin: Queueing bin, used to enqueue using QDID, DQBIN, QPRI. Only relevant * for Tx queues.
*/ struct dpni_queue_id {
u32 fqid;
u16 qdbin;
};
/* Set User Context */ #define DPNI_QUEUE_OPT_USER_CTX 0x00000001 #define DPNI_QUEUE_OPT_DEST 0x00000002 #define DPNI_QUEUE_OPT_FLC 0x00000004 #define DPNI_QUEUE_OPT_HOLD_ACTIVE 0x00000008
/** * enum dpni_congestion_unit - DPNI congestion units * @DPNI_CONGESTION_UNIT_BYTES: bytes units * @DPNI_CONGESTION_UNIT_FRAMES: frames units
*/ enum dpni_congestion_unit {
DPNI_CONGESTION_UNIT_BYTES = 0,
DPNI_CONGESTION_UNIT_FRAMES
};
/** * enum dpni_congestion_point - Structure representing congestion point * @DPNI_CP_QUEUE: Set taildrop per queue, identified by QUEUE_TYPE, TC and * QUEUE_INDEX * @DPNI_CP_GROUP: Set taildrop per queue group. Depending on options used to * define the DPNI this can be either per TC (default) or per * interface (DPNI_OPT_SHARED_CONGESTION set at DPNI create). * QUEUE_INDEX is ignored if this type is used.
*/ enum dpni_congestion_point {
DPNI_CP_QUEUE,
DPNI_CP_GROUP,
};
/** * struct dpni_dest_cfg - Structure representing DPNI destination parameters * @dest_type: Destination type * @dest_id: Either DPIO ID or DPCON ID, depending on the destination type * @priority: Priority selection within the DPIO or DPCON channel; valid * values are 0-1 or 0-7, depending on the number of priorities * in that channel; not relevant for 'DPNI_DEST_NONE' option
*/ struct dpni_dest_cfg { enum dpni_dest dest_type; int dest_id;
u8 priority;
};
/* DPNI congestion options */
/** * DPNI_CONG_OPT_FLOW_CONTROL - This congestion will trigger flow control or * priority flow control. This will have effect only if flow control is * enabled with dpni_set_link_cfg().
*/ #define DPNI_CONG_OPT_FLOW_CONTROL 0x00000040
/** * struct dpni_congestion_notification_cfg - congestion notification * configuration * @units: Units type * @threshold_entry: Above this threshold we enter a congestion state. * set it to '0' to disable it * @threshold_exit: Below this threshold we exit the congestion state. * @message_ctx: The context that will be part of the CSCN message * @message_iova: I/O virtual address (must be in DMA-able memory), * must be 16B aligned; valid only if 'DPNI_CONG_OPT_WRITE_MEM_<X>' * is contained in 'options' * @dest_cfg: CSCN can be send to either DPIO or DPCON WQ channel * @notification_mode: Mask of available options; use 'DPNI_CONG_OPT_<X>' values
*/
/** * struct dpni_taildrop - Structure representing the taildrop * @enable: Indicates whether the taildrop is active or not. * @units: Indicates the unit of THRESHOLD. Queue taildrop only supports * byte units, this field is ignored and assumed = 0 if * CONGESTION_POINT is 0. * @threshold: Threshold value, in units identified by UNITS field. Value 0 * cannot be used as a valid taildrop threshold, THRESHOLD must * be > 0 if the taildrop is enabled.
*/ struct dpni_taildrop { char enable; enum dpni_congestion_unit units;
u32 threshold;
};
/** * struct dpni_rule_cfg - Rule configuration for table lookup * @key_iova: I/O virtual address of the key (must be in DMA-able memory) * @mask_iova: I/O virtual address of the mask (must be in DMA-able memory) * @key_size: key and mask size (in bytes)
*/ struct dpni_rule_cfg {
u64 key_iova;
u64 mask_iova;
u8 key_size;
};
/** * DPNI_FS_OPT_DISCARD - Discard matching traffic. If set, this takes * precedence over any other configuration and matching traffic is always * discarded.
*/ #define DPNI_FS_OPT_DISCARD 0x1
/** * DPNI_FS_OPT_SET_FLC - Set FLC value. If set, flc member of struct * dpni_fs_action_cfg is used to override the FLC value set per queue. * For more details check the Frame Descriptor section in the hardware * documentation.
*/ #define DPNI_FS_OPT_SET_FLC 0x2
/** * DPNI_FS_OPT_SET_STASH_CONTROL - Indicates whether the 6 lowest significant * bits of FLC are used for stash control. If set, the 6 least significant bits * in value are interpreted as follows: * - bits 0-1: indicates the number of 64 byte units of context that are * stashed. FLC value is interpreted as a memory address in this case, * excluding the 6 LS bits. * - bits 2-3: indicates the number of 64 byte units of frame annotation * to be stashed. Annotation is placed at FD[ADDR]. * - bits 4-5: indicates the number of 64 byte units of frame data to be * stashed. Frame data is placed at FD[ADDR] + FD[OFFSET]. * This flag is ignored if DPNI_FS_OPT_SET_FLC is not specified.
*/ #define DPNI_FS_OPT_SET_STASH_CONTROL 0x4
/** * struct dpni_fs_action_cfg - Action configuration for table look-up * @flc: FLC value for traffic matching this rule. Please check the * Frame Descriptor section in the hardware documentation for * more information. * @flow_id: Identifies the Rx queue used for matching traffic. Supported * values are in range 0 to num_queue-1. * @options: Any combination of DPNI_FS_OPT_ values.
*/ struct dpni_fs_action_cfg {
u64 flc;
u16 flow_id;
u16 options;
};
int dpni_set_tx_shaping(struct fsl_mc_io *mc_io,
u32 cmd_flags,
u16 token, conststruct dpni_tx_shaping_cfg *tx_cr_shaper, conststruct dpni_tx_shaping_cfg *tx_er_shaper, int coupled);
/** * struct dpni_single_step_cfg - configure single step PTP (IEEE 1588) * @en: enable single step PTP. When enabled the PTPv1 functionality * will not work. If the field is zero, offset and ch_update * parameters will be ignored * @offset: start offset from the beginning of the frame where * timestamp field is found. The offset must respect all MAC * headers, VLAN tags and other protocol headers * @ch_update: when set UDP checksum will be updated inside packet * @peer_delay: For peer-to-peer transparent clocks add this value to the * correction field in addition to the transient time update. * The value expresses nanoseconds. * @ptp_onestep_reg_base: 1588 SINGLE_STEP register base address. This address * is used to update directly the register contents. * User has to create an address mapping for it. * *
*/ struct dpni_single_step_cfg {
u8 en;
u8 ch_update;
u16 offset;
u32 peer_delay;
u32 ptp_onestep_reg_base;
};
Die Informationen auf dieser Webseite wurden
nach bestem Wissen sorgfältig zusammengestellt. Es wird jedoch weder Vollständigkeit, noch Richtigkeit,
noch Qualität der bereit gestellten Informationen zugesichert.
Bemerkung:
Die farbliche Syntaxdarstellung und die Messung sind noch experimentell.