Quelle  sa8775p-ride.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2023, Linaro Limited
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>

#include "sa8775p.dtsi"
#include "sa8775p-pmics.dtsi"

/ {
 aliases {
  ethernet0 = ðernet0;
  ethernet1 = ðernet1;
  i2c11 = &i2c11;
  i2c18 = &i2c18;
  serial0 = &uart10;
  serial1 = &uart12;
  serial2 = &uart17;
  spi16 = &spi16;
  ufshc1 = &ufs_mem_hc;
 };

 chosen {
  stdout-path = "serial0:115200n8";
 };

 vreg_12p0: vreg-12p0-regulator {
  compatible = "regulator-fixed";
  regulator-name = "VREG_12P0";

  regulator-always-on;
  regulator-boot-on;
  regulator-min-microvolt = <12000000>;
  regulator-max-microvolt = <12000000>;
 };

 vreg_5p0: vreg-5p0-regulator {
  compatible = "regulator-fixed";
  regulator-name = "VREG_5P0";

  regulator-always-on;
  regulator-boot-on;
  regulator-min-microvolt = <5000000>;
  regulator-max-microvolt = <5000000>;

  vin-supply = <&vreg_12p0>;
 };

 vreg_1p8: vreg-1p8-regulator {
  compatible = "regulator-fixed";
  regulator-name = "VREG_1P8";

  regulator-always-on;
  regulator-boot-on;
  regulator-min-microvolt = <1800000>;
  regulator-max-microvolt = <1800000>;

  vin-supply = <&vreg_5p0>;
 };

 vreg_1p0: vreg-1p0-regulator {
  compatible = "regulator-fixed";
  regulator-name = "VREG_1P0";

  regulator-always-on;
  regulator-boot-on;
  regulator-min-microvolt = <1000000>;
  regulator-max-microvolt = <1000000>;

  vin-supply = <&vreg_1p8>;
 };

 vreg_3p0: vreg-3p0-regulator {
  compatible = "regulator-fixed";
  regulator-name = "VREG_3P0";

  regulator-always-on;
  regulator-boot-on;
  regulator-min-microvolt = <3000000>;
  regulator-max-microvolt = <3000000>;

  vin-supply = <&vreg_12p0>;
 };

 vreg_conn_1p8: vreg_conn_1p8 {
  compatible = "regulator-fixed";
  regulator-name = "vreg_conn_1p8";
  startup-delay-us = <4000>;
  enable-active-high;
  gpio = <&pmm8654au_1_gpios 4 GPIO_ACTIVE_HIGH>;
 };

 vreg_conn_pa: vreg_conn_pa {
  compatible = "regulator-fixed";
  regulator-name = "vreg_conn_pa";
  startup-delay-us = <4000>;
  enable-active-high;
  gpio = <&pmm8654au_1_gpios 6 GPIO_ACTIVE_HIGH>;
 };

 wcn6855-pmu {
  compatible = "qcom,wcn6855-pmu";

  pinctrl-names = "default";
  pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;

  vddio-supply = <&vreg_conn_pa>;
  vddaon-supply = <&vreg_l2c>;
  vddpmu-supply = <&vreg_conn_1p8>;
  vddrfa0p95-supply = <&vreg_l2c>;
  vddrfa1p3-supply = <&vreg_l6e>;
  vddrfa1p9-supply = <&vreg_s5a>;
  vddpcie1p3-supply = <&vreg_l6e>;
  vddpcie1p9-supply = <&vreg_s5a>;

  bt-enable-gpios = <&pmm8654au_1_gpios 8 GPIO_ACTIVE_HIGH>;
  wlan-enable-gpios = <&pmm8654au_1_gpios 7 GPIO_ACTIVE_HIGH>;

  regulators {
   vreg_pmu_rfa_cmn: ldo0 {
    regulator-name = "vreg_pmu_rfa_cmn";
   };

   vreg_pmu_aon_0p59: ldo1 {
    regulator-name = "vreg_pmu_aon_0p59";
   };

   vreg_pmu_wlcx_0p8: ldo2 {
    regulator-name = "vreg_pmu_wlcx_0p8";
   };

   vreg_pmu_wlmx_0p85: ldo3 {
    regulator-name = "vreg_pmu_wlmx_0p85";
   };

   vreg_pmu_btcmx_0p85: ldo4 {
    regulator-name = "vreg_pmu_btcmx_0p85";
   };

   vreg_pmu_rfa_0p8: ldo5 {
    regulator-name = "vreg_pmu_rfa_0p8";
   };

   vreg_pmu_rfa_1p2: ldo6 {
    regulator-name = "vreg_pmu_rfa_1p2";
   };

   vreg_pmu_rfa_1p7: ldo7 {
    regulator-name = "vreg_pmu_rfa_1p7";
   };

   vreg_pmu_pcie_0p9: ldo8 {
    regulator-name = "vreg_pmu_pcie_0p9";
   };

   vreg_pmu_pcie_1p8: ldo9 {
    regulator-name = "vreg_pmu_pcie_1p8";
   };
  };
 };

 dp0-connector {
  compatible = "dp-connector";
  label = "eDP0";
  type = "full-size";

  port {
   dp0_connector_in: endpoint {
    remote-endpoint = <&mdss0_dp0_out>;
   };
  };
 };

 dp1-connector {
  compatible = "dp-connector";
  label = "eDP1";
  type = "full-size";

  port {
   dp1_connector_in: endpoint {
    remote-endpoint = <&mdss0_dp1_out>;
   };
  };
 };

 dp-dsi0-connector {
  compatible = "dp-connector";
  label = "DSI0";
  type = "full-size";

  port {
   dp_dsi0_connector_in: endpoint {
    remote-endpoint = <&dsi2dp_bridge0_out>;
   };
  };
 };

 dp-dsi1-connector {
  compatible = "dp-connector";
  label = "DSI1";
  type = "full-size";

  port {
   dp_dsi1_connector_in: endpoint {
    remote-endpoint = <&dsi2dp_bridge1_out>;
   };
  };
 };
};

&apps_rsc {
 regulators-0 {
  compatible = "qcom,pmm8654au-rpmh-regulators";
  qcom,pmic-id = "a";

  vreg_s4a: smps4 {
   regulator-name = "vreg_s4a";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1816000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s5a: smps5 {
   regulator-name = "vreg_s5a";
   regulator-min-microvolt = <1850000>;
   regulator-max-microvolt = <1996000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s9a: smps9 {
   regulator-name = "vreg_s9a";
   regulator-min-microvolt = <535000>;
   regulator-max-microvolt = <1120000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l4a: ldo4 {
   regulator-name = "vreg_l4a";
   regulator-min-microvolt = <788000>;
   regulator-max-microvolt = <1050000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l5a: ldo5 {
   regulator-name = "vreg_l5a";
   regulator-min-microvolt = <870000>;
   regulator-max-microvolt = <950000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6a: ldo6 {
   regulator-name = "vreg_l6a";
   regulator-min-microvolt = <870000>;
   regulator-max-microvolt = <970000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7a: ldo7 {
   regulator-name = "vreg_l7a";
   regulator-min-microvolt = <720000>;
   regulator-max-microvolt = <950000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l8a: ldo8 {
   regulator-name = "vreg_l8a";
   regulator-min-microvolt = <2504000>;
   regulator-max-microvolt = <3300000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l9a: ldo9 {
   regulator-name = "vreg_l9a";
   regulator-min-microvolt = <2970000>;
   regulator-max-microvolt = <3544000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-1 {
  compatible = "qcom,pmm8654au-rpmh-regulators";
  qcom,pmic-id = "c";

  vreg_l1c: ldo1 {
   regulator-name = "vreg_l1c";
   regulator-min-microvolt = <1140000>;
   regulator-max-microvolt = <1260000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l2c: ldo2 {
   regulator-name = "vreg_l2c";
   regulator-min-microvolt = <900000>;
   regulator-max-microvolt = <1100000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l3c: ldo3 {
   regulator-name = "vreg_l3c";
   regulator-min-microvolt = <1100000>;
   regulator-max-microvolt = <1300000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l4c: ldo4 {
   regulator-name = "vreg_l4c";
   regulator-min-microvolt = <1200000>;
   regulator-max-microvolt = <1200000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   /*
    * FIXME: This should have regulator-allow-set-load but
    * we're getting an over-current fault from the PMIC
    * when switching to LPM.
    */
  };

  vreg_l5c: ldo5 {
   regulator-name = "vreg_l5c";
   regulator-min-microvolt = <1100000>;
   regulator-max-microvolt = <1300000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6c: ldo6 {
   regulator-name = "vreg_l6c";
   regulator-min-microvolt = <1620000>;
   regulator-max-microvolt = <1980000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l7c: ldo7 {
   regulator-name = "vreg_l7c";
   regulator-min-microvolt = <1620000>;
   regulator-max-microvolt = <2000000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l8c: ldo8 {
   regulator-name = "vreg_l8c";
   regulator-min-microvolt = <2400000>;
   regulator-max-microvolt = <3300000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l9c: ldo9 {
   regulator-name = "vreg_l9c";
   regulator-min-microvolt = <1650000>;
   regulator-max-microvolt = <2700000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };

 regulators-2 {
  compatible = "qcom,pmm8654au-rpmh-regulators";
  qcom,pmic-id = "e";

  vreg_s4e: smps4 {
   regulator-name = "vreg_s4e";
   regulator-min-microvolt = <970000>;
   regulator-max-microvolt = <1520000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s7e: smps7 {
   regulator-name = "vreg_s7e";
   regulator-min-microvolt = <1010000>;
   regulator-max-microvolt = <1170000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_s9e: smps9 {
   regulator-name = "vreg_s9e";
   regulator-min-microvolt = <300000>;
   regulator-max-microvolt = <570000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l6e: ldo6 {
   regulator-name = "vreg_l6e";
   regulator-min-microvolt = <1280000>;
   regulator-max-microvolt = <1450000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };

  vreg_l8e: ldo8 {
   regulator-name = "vreg_l8e";
   regulator-min-microvolt = <1800000>;
   regulator-max-microvolt = <1950000>;
   regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
   regulator-allow-set-load;
   regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
         RPMH_REGULATOR_MODE_HPM>;
  };
 };
};

ðernet0 {
 phy-handle = <&sgmii_phy0>;

 pinctrl-0 = <ðernet0_default>;
 pinctrl-names = "default";

 snps,mtl-rx-config = <&mtl_rx_setup>;
 snps,mtl-tx-config = <&mtl_tx_setup>;
 snps,ps-speed = <1000>;

 status = "okay";

 mdio: mdio {
  compatible = "snps,dwmac-mdio";
  #address-cells = <1>;
  #size-cells = <0>;
 };

 mtl_rx_setup: rx-queues-config {
  snps,rx-queues-to-use = <4>;
  snps,rx-sched-sp;

  queue0 {
   snps,dcb-algorithm;
   snps,map-to-dma-channel = <0x0>;
   snps,route-up;
   snps,priority = <0x1>;
  };

  queue1 {
   snps,dcb-algorithm;
   snps,map-to-dma-channel = <0x1>;
   snps,route-ptp;
  };

  queue2 {
   snps,avb-algorithm;
   snps,map-to-dma-channel = <0x2>;
   snps,route-avcp;
  };

  queue3 {
   snps,avb-algorithm;
   snps,map-to-dma-channel = <0x3>;
   snps,priority = <0xc>;
  };
 };

 mtl_tx_setup: tx-queues-config {
  snps,tx-queues-to-use = <4>;

  queue0 {
   snps,dcb-algorithm;
  };

  queue1 {
   snps,dcb-algorithm;
  };

  queue2 {
   snps,avb-algorithm;
   snps,send_slope = <0x1000>;
   snps,idle_slope = <0x1000>;
   snps,high_credit = <0x3e800>;
   snps,low_credit = <0xffc18000>;
  };

  queue3 {
   snps,avb-algorithm;
   snps,send_slope = <0x1000>;
   snps,idle_slope = <0x1000>;
   snps,high_credit = <0x3e800>;
   snps,low_credit = <0xffc18000>;
  };
 };
};

ðernet1 {
 phy-handle = <&sgmii_phy1>;

 snps,mtl-rx-config = <&mtl_rx_setup1>;
 snps,mtl-tx-config = <&mtl_tx_setup1>;
 snps,ps-speed = <1000>;

 status = "okay";

 mtl_rx_setup1: rx-queues-config {
  snps,rx-queues-to-use = <4>;
  snps,rx-sched-sp;

  queue0 {
   snps,dcb-algorithm;
   snps,map-to-dma-channel = <0x0>;
   snps,route-up;
   snps,priority = <0x1>;
  };

  queue1 {
   snps,dcb-algorithm;
   snps,map-to-dma-channel = <0x1>;
   snps,route-ptp;
  };

  queue2 {
   snps,avb-algorithm;
   snps,map-to-dma-channel = <0x2>;
   snps,route-avcp;
  };

  queue3 {
   snps,avb-algorithm;
   snps,map-to-dma-channel = <0x3>;
   snps,priority = <0xc>;
  };
 };

 mtl_tx_setup1: tx-queues-config {
  snps,tx-queues-to-use = <4>;

  queue0 {
   snps,dcb-algorithm;
  };

  queue1 {
   snps,dcb-algorithm;
  };

  queue2 {
   snps,avb-algorithm;
   snps,send_slope = <0x1000>;
   snps,idle_slope = <0x1000>;
   snps,high_credit = <0x3e800>;
   snps,low_credit = <0xffc18000>;
  };

  queue3 {
   snps,avb-algorithm;
   snps,send_slope = <0x1000>;
   snps,idle_slope = <0x1000>;
   snps,high_credit = <0x3e800>;
   snps,low_credit = <0xffc18000>;
  };
 };
};

&i2c11 {
 clock-frequency = <400000>;
 status = "okay";
};

&i2c18 {
 clock-frequency = <400000>;

 status = "okay";

 io_expander: gpio@74 {
  compatible = "ti,tca9539";
  reg = <0x74>;
  interrupts-extended = <&tlmm 98 IRQ_TYPE_EDGE_BOTH>;
  gpio-controller;
  #gpio-cells = <2>;
  interrupt-controller;
  #interrupt-cells = <2>;
  reset-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;

  pinctrl-0 = <&io_expander_intr_active>,
       <&io_expander_reset_active>;
  pinctrl-names = "default";
 };

 i2c-mux@70 {
  compatible = "nxp,pca9543";
  #address-cells = <1>;

  #size-cells = <0>;
  reg = <0x70>;

  i2c@0 {
   reg = <0>;
   #address-cells = <1>;
   #size-cells = <0>;

   bridge@58 {
    compatible = "analogix,anx7625";
    reg = <0x58>;
    interrupts-extended = <&io_expander 2 IRQ_TYPE_EDGE_FALLING>;
    enable-gpios = <&io_expander 1 GPIO_ACTIVE_HIGH>;
    reset-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
    vdd10-supply = <&vreg_1p0>;
    vdd18-supply = <&vreg_1p8>;
    vdd33-supply = <&vreg_3p0>;

    ports {
     #address-cells = <1>;
     #size-cells = <0>;

     port@0 {
      reg = <0>;

      dsi2dp_bridge0_in: endpoint {
       remote-endpoint = <&mdss0_dsi0_out>;
      };
     };

     port@1 {
      reg = <1>;

      dsi2dp_bridge0_out: endpoint {
       remote-endpoint = <&dp_dsi0_connector_in>;
      };
     };
    };
   };
  };

  i2c@1 {
   reg = <1>;
   #address-cells = <1>;
   #size-cells = <0>;

   bridge@58 {
    compatible = "analogix,anx7625";
    reg = <0x58>;
    interrupts-extended = <&io_expander 10 IRQ_TYPE_EDGE_FALLING>;
    enable-gpios = <&io_expander 9 GPIO_ACTIVE_HIGH>;
    reset-gpios = <&io_expander 8 GPIO_ACTIVE_HIGH>;
    vdd10-supply = <&vreg_1p0>;
    vdd18-supply = <&vreg_1p8>;
    vdd33-supply = <&vreg_3p0>;

    ports {
     #address-cells = <1>;
     #size-cells = <0>;

     port@0 {
      reg = <0>;

      dsi2dp_bridge1_in: endpoint {
       remote-endpoint = <&mdss0_dsi1_out>;
      };
     };

     port@1 {
      reg = <1>;

      dsi2dp_bridge1_out: endpoint {
       remote-endpoint = <&dp_dsi1_connector_in>;
      };
     };
    };
   };
  };
 };

};

&iris {
 firmware-name = "qcom/vpu/vpu30_p4_s6.mbn";

 status = "okay";
};

&mdss0 {
 status = "okay";
};

&mdss0_dp0 {
 pinctrl-0 = <&dp0_hot_plug_det>;
 pinctrl-names = "default";

 status = "okay";
};

&mdss0_dp0_out {
 data-lanes = <0 1 2 3>;
 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
 remote-endpoint = <&dp0_connector_in>;
};

&mdss0_dp0_phy {
 vdda-phy-supply = <&vreg_l1c>;
 vdda-pll-supply = <&vreg_l4a>;

 status = "okay";
};

&mdss0_dp1 {
 pinctrl-0 = <&dp1_hot_plug_det>;
 pinctrl-names = "default";

 status = "okay";
};

&mdss0_dp1_out {
 data-lanes = <0 1 2 3>;
 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
 remote-endpoint = <&dp1_connector_in>;
};

&mdss0_dp1_phy {
 vdda-phy-supply = <&vreg_l1c>;
 vdda-pll-supply = <&vreg_l4a>;

 status = "okay";
};

&mdss0_dsi0 {
 vdda-supply = <&vreg_l1c>;

 status = "okay";
};

&mdss0_dsi0_out {
 data-lanes = <0 1 2 3>;
 remote-endpoint = <&dsi2dp_bridge0_in>;
};

&mdss0_dsi0_phy {
 vdds-supply = <&vreg_l4a>;

 status = "okay";
};

&mdss0_dsi1 {
 vdda-supply = <&vreg_l1c>;

 status = "okay";
};

&mdss0_dsi1_out {
 data-lanes = <0 1 2 3>;
 remote-endpoint = <&dsi2dp_bridge1_in>;
};

&mdss0_dsi1_phy {
 vdds-supply = <&vreg_l4a>;

 status = "okay";
};

&pmm8654au_0_gpios {
 gpio-line-names = "DS_EN",
     "POFF_COMPLETE",
     "UFS0_VER_ID",
     "FAST_POFF",
     "DBU1_PON_DONE",
     "AOSS_SLEEP",
     "CAM_DES0_EN",
     "CAM_DES1_EN",
     "CAM_DES2_EN",
     "CAM_DES3_EN",
     "UEFI",
     "ANALOG_PON_OPT";
};

&pmm8654au_0_pon_resin {
 linux,code = <KEY_VOLUMEDOWN>;
 status = "okay";
};

&pmm8654au_1_gpios {
 gpio-line-names = "PMIC_C_ID0",
     "PMIC_C_ID1",
     "UFS1_VER_ID",
     "IPA_PWR",
     "",
     "WLAN_DBU4_EN",
     "WLAN_EN",
     "BT_EN",
     "USB2_PWR_EN",
     "USB2_FAULT";

 wlan_en_state: wlan-en-state {
  pins = "gpio7";
  function = "normal";
  output-low;
  bias-pull-down;
 };

 bt_en_state: bt-en-state {
  pins = "gpio8";
  function = "normal";
  output-low;
  bias-pull-down;
 };

 usb2_en_state: usb2-en-state {
  pins = "gpio9";
  function = "normal";
  output-high;
  power-source = <0>;
 };
};

&pmm8654au_2_gpios {
 gpio-line-names = "PMIC_E_ID0",
     "PMIC_E_ID1",
     "USB0_PWR_EN",
     "USB0_FAULT",
     "SENSOR_IRQ_1",
     "SENSOR_IRQ_2",
     "SENSOR_RST",
     "SGMIIO0_RST",
     "SGMIIO1_RST",
     "USB1_PWR_ENABLE",
     "USB1_FAULT",
     "VMON_SPX8";

 usb0_en_state: usb0-en-state {
  pins = "gpio3";
  function = "normal";
  output-high;
  power-source = <0>;
 };

 usb1_en_state: usb1-en-state {
  pins = "gpio10";
  function = "normal";
  output-high;
  power-source = <0>;
 };
};

&pmm8654au_3_gpios {
 gpio-line-names = "PMIC_G_ID0",
     "PMIC_G_ID1",
     "GNSS_RST",
     "GNSS_EN",
     "GNSS_BOOT_MODE";
};

&qupv3_id_1 {
 status = "okay";
};

&qupv3_id_2 {
 status = "okay";
};

&qup_spi16_default {
 drive-strength = <6>;
 bias-disable;
};

&qup_i2c11_default {
 drive-strength = <2>;
 bias-pull-up;
};

&qup_i2c18_default {
 drive-strength = <2>;
 bias-pull-up;
};

&qup_uart12_cts {
 bias-disable;
};

&qup_uart12_rts {
 bias-pull-down;
};

&qup_uart12_tx {
 bias-pull-up;
};

&qup_uart12_rx {
 bias-pull-down;
};

&qup_uart17_cts {
 bias-disable;
};

&qup_uart17_rts {
 bias-pull-down;
};

&qup_uart17_tx {
 bias-pull-up;
};

&qup_uart17_rx {
 bias-pull-down;
};

&serdes0 {
 phy-supply = <&vreg_l5a>;
 status = "okay";
};

&serdes1 {
 phy-supply = <&vreg_l5a>;
 status = "okay";
};

&sleep_clk {
 clock-frequency = <32000>;
};

&spi16 {
 status = "okay";
};

&tlmm {
 dp0_hot_plug_det: dp0-hot-plug-det-state {
  pins = "gpio101";
  function = "edp0_hot";
  bias-disable;
 };

 dp1_hot_plug_det: dp1-hot-plug-det-state {
  pins = "gpio102";
  function = "edp1_hot";
  bias-disable;
 };

 ethernet0_default: ethernet0-default-state {
  ethernet0_mdc: ethernet0-mdc-pins {
   pins = "gpio8";
   function = "emac0_mdc";
   drive-strength = <16>;
   bias-pull-up;
  };

  ethernet0_mdio: ethernet0-mdio-pins {
   pins = "gpio9";
   function = "emac0_mdio";
   drive-strength = <16>;
   bias-pull-up;
  };
 };

 io_expander_intr_active: io-expander-intr-active-state {
  pins = "gpio98";
  function = "gpio";
  drive-strength = <2>;
  bias-disable;
 };

 io_expander_reset_active: io-expander-reset-active-state {
  pins = "gpio97";
  function = "gpio";
  drive-strength = <2>;
  bias-disable;
  output-high;
 };

 pcie0_default_state: pcie0-default-state {
  perst-pins {
   pins = "gpio2";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-down;
  };

  clkreq-pins {
   pins = "gpio1";
   function = "pcie0_clkreq";
   drive-strength = <2>;
   bias-pull-up;
  };

  wake-pins {
   pins = "gpio0";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-up;
  };
 };

 pcie1_default_state: pcie1-default-state {
  perst-pins {
   pins = "gpio4";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-down;
  };

  clkreq-pins {
   pins = "gpio3";
   function = "pcie1_clkreq";
   drive-strength = <2>;
   bias-pull-up;
  };

  wake-pins {
   pins = "gpio5";
   function = "gpio";
   drive-strength = <2>;
   bias-pull-up;
  };
 };
};

&pcie0 {
 perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
 wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;

 pinctrl-names = "default";
 pinctrl-0 = <&pcie0_default_state>;

 status = "okay";
};

&pcie1 {
 perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
 wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;

 pinctrl-names = "default";
 pinctrl-0 = <&pcie1_default_state>;

 status = "okay";
};

&pcie0_phy {
 vdda-phy-supply = <&vreg_l5a>;
 vdda-pll-supply = <&vreg_l1c>;

 status = "okay";
};

&pcie1_phy {
 vdda-phy-supply = <&vreg_l5a>;
 vdda-pll-supply = <&vreg_l1c>;

 status = "okay";
};

&pcieport0 {
 wifi@0 {
  compatible = "pci17cb,1101";
  reg = <0x10000 0x0 0x0 0x0 0x0>;

  qcom,calibration-variant = "QC_SA8775P_Ride";

  vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
  vddaon-supply = <&vreg_pmu_aon_0p59>;
  vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
  vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
  vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
  vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
  vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
  vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
  vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
 };
};

&remoteproc_adsp {
 firmware-name = "qcom/sa8775p/adsp.mbn";
 status = "okay";
};

&remoteproc_cdsp0 {
 firmware-name = "qcom/sa8775p/cdsp0.mbn";
 status = "okay";
};

&remoteproc_cdsp1 {
 firmware-name = "qcom/sa8775p/cdsp1.mbn";
 status = "okay";
};

&remoteproc_gpdsp0 {
 firmware-name = "qcom/sa8775p/gpdsp0.mbn";
 status = "okay";
};

&remoteproc_gpdsp1 {
 firmware-name = "qcom/sa8775p/gpdsp1.mbn";
 status = "okay";
};

&uart10 {
 compatible = "qcom,geni-debug-uart";
 status = "okay";
};

&uart12 {
 pinctrl-0 = <&qup_uart12_default>;
 pinctrl-names = "default";
 status = "okay";
};

&uart17 {
 pinctrl-0 = <&qup_uart17_default>;
 pinctrl-names = "default";
 status = "okay";

 bluetooth {
  compatible = "qcom,wcn6855-bt";
  firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";

  vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
  vddaon-supply = <&vreg_pmu_aon_0p59>;
  vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
  vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
  vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
  vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
 };
};

&ufs_mem_hc {
 reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
 vcc-supply = <&vreg_l8a>;
 vcc-max-microamp = <1100000>;
 vccq-supply = <&vreg_l4c>;
 vccq-max-microamp = <1200000>;

 status = "okay";
};

&ufs_mem_phy {
 vdda-phy-supply = <&vreg_l4a>;
 vdda-pll-supply = <&vreg_l1c>;

 status = "okay";
};

&usb_0 {
 pinctrl-names = "default";
 pinctrl-0 = <&usb0_en_state>;

 status = "okay";
};

&usb_0_dwc3 {
 dr_mode = "peripheral";
};

&usb_0_hsphy {
 vdda-pll-supply = <&vreg_l7a>;
 vdda18-supply = <&vreg_l6c>;
 vdda33-supply = <&vreg_l9a>;

 status = "okay";
};

&usb_0_qmpphy {
 vdda-phy-supply = <&vreg_l1c>;
 vdda-pll-supply = <&vreg_l7a>;

 status = "okay";
};

&usb_1 {
 pinctrl-names = "default";
 pinctrl-0 = <&usb1_en_state>;

 status = "okay";
};

&usb_1_dwc3 {
 dr_mode = "host";
};

&usb_1_hsphy {
 vdda-pll-supply = <&vreg_l7a>;
 vdda18-supply = <&vreg_l6c>;
 vdda33-supply = <&vreg_l9a>;

 status = "okay";
};

&usb_1_qmpphy {
 vdda-phy-supply = <&vreg_l1c>;
 vdda-pll-supply = <&vreg_l7a>;

 status = "okay";
};

&usb_2 {
 pinctrl-names = "default";
 pinctrl-0 = <&usb2_en_state>;

 status = "okay";
};

&usb_2_dwc3 {
 dr_mode = "host";
};

&usb_2_hsphy {
 vdda-pll-supply = <&vreg_l7a>;
 vdda18-supply = <&vreg_l6c>;
 vdda33-supply = <&vreg_l9a>;

 status = "okay";
};

&xo_board_clk {
 clock-frequency = <38400000>;
};