/* SPDX-License-Identifier: GPL-2.0-or-later */ /* * Copyright (C) 2003 - 2009 NetXen, Inc. * Copyright (C) 2009 - QLogic Corporation. * All rights reserved. #ifndef __NETXEN_NIC_HW_H_#define __NETXEN_NIC_HW_H_/* Hardware memory size of 128 meg */ #define NETXEN_MEMADDR_MAX (128 * 1024 * 1024 )struct netxen_adapter;#define NETXEN_PCI_MAPSIZE_BYTES (NETXEN_PCI_MAPSIZE << 20 )void netxen_nic_set_link_parameters(struct netxen_adapter *adapter);/* Nibble or Byte mode for phy interface (GbE mode only) */ #define _netxen_crb_get_bit(var, bit) ((var >> bit) & 0 x1)/* * NIU GB MAC Config Register 0 (applies to GB0, GB1, GB2, GB3) * * Bit 0 : enable_tx => 1:enable frame xmit, 0:disable * Bit 1 : tx_synced => R/O: xmit enable synched to xmit stream * Bit 2 : enable_rx => 1:enable frame recv, 0:disable * Bit 3 : rx_synced => R/O: recv enable synched to recv stream * Bit 4 : tx_flowctl => 1:enable pause frame generation, 0:disable * Bit 5 : rx_flowctl => 1:act on recv'd pause frames, 0:ignore * Bit 8 : loopback => 1:loop MAC xmits to MAC recvs, 0:normal * Bit 16: tx_reset_pb => 1:reset frame xmit protocol blk, 0:no-op * Bit 17: rx_reset_pb => 1:reset frame recv protocol blk, 0:no-op * Bit 18: tx_reset_mac => 1:reset data/ctl multiplexer blk, 0:no-op * Bit 19: rx_reset_mac => 1:reset ctl frames & timers blk, 0:no-op * Bit 31: soft_reset => 1:reset the MAC and the SERDES, 0:no-op #define netxen_gb_tx_flowctl(config_word) \1 << 4 )#define netxen_gb_rx_flowctl(config_word) \1 << 5 )#define netxen_gb_tx_reset_pb(config_word) \1 << 16 )#define netxen_gb_rx_reset_pb(config_word) \1 << 17 )#define netxen_gb_tx_reset_mac(config_word) \1 << 18 )#define netxen_gb_rx_reset_mac(config_word) \1 << 19 )#define netxen_gb_unset_tx_flowctl(config_word) \1 << 4 ))#define netxen_gb_unset_rx_flowctl(config_word) \1 << 5 ))#define netxen_gb_get_tx_synced(config_word) \1 )#define netxen_gb_get_rx_synced(config_word) \3 )#define netxen_gb_get_tx_flowctl(config_word) \4 )#define netxen_gb_get_rx_flowctl(config_word) \5 )#define netxen_gb_get_soft_reset(config_word) \31 )#define netxen_gb_get_stationaddress_low(config_word) ((config_word) >> 16 )#define netxen_gb_set_mii_mgmt_clockselect(config_word, val) \0 x07))#define netxen_gb_mii_mgmt_reset(config_word) \1 << 31 )#define netxen_gb_mii_mgmt_unset(config_word) \1 << 31 ))/* * NIU GB MII Mgmt Command Register (applies to GB0, GB1, GB2, GB3) * Bit 0 : read_cycle => 1:perform single read cycle, 0:no-op * Bit 1 : scan_cycle => 1:perform continuous read cycles, 0:no-op #define netxen_gb_mii_mgmt_set_read_cycle(config_word) \1 << 0 )#define netxen_gb_mii_mgmt_reg_addr(config_word, val) \0 x1F))#define netxen_gb_mii_mgmt_phy_addr(config_word, val) \0 x1F) << 8 ))/* * NIU GB MII Mgmt Indicators Register (applies to GB0, GB1, GB2, GB3) * Read-only register. * Bit 0 : busy => 1:performing an MII mgmt cycle, 0:idle * Bit 1 : scanning => 1:scan operation in progress, 0:idle * Bit 2 : notvalid => :mgmt result data not yet valid, 0:idle #define netxen_get_gb_mii_mgmt_busy(config_word) \0 )#define netxen_get_gb_mii_mgmt_scanning(config_word) \1 )#define netxen_get_gb_mii_mgmt_notvalid(config_word) \2 )/* * NIU XG Pause Ctl Register * * Bit 0 : xg0_mask => 1:disable tx pause frames * Bit 1 : xg0_request => 1:request single pause frame * Bit 2 : xg0_on_off => 1:request is pause on, 0:off * Bit 3 : xg1_mask => 1:disable tx pause frames * Bit 4 : xg1_request => 1:request single pause frame * Bit 5 : xg1_on_off => 1:request is pause on, 0:off #define netxen_xg_set_xg0_mask(config_word) \1 << 0 )#define netxen_xg_set_xg1_mask(config_word) \1 << 3 )#define netxen_xg_get_xg0_mask(config_word) \0 )#define netxen_xg_get_xg1_mask(config_word) \3 )#define netxen_xg_unset_xg0_mask(config_word) \1 << 0 ))#define netxen_xg_unset_xg1_mask(config_word) \1 << 3 ))/* * NIU XG Pause Ctl Register * * Bit 0 : xg0_mask => 1:disable tx pause frames * Bit 1 : xg0_request => 1:request single pause frame * Bit 2 : xg0_on_off => 1:request is pause on, 0:off * Bit 3 : xg1_mask => 1:disable tx pause frames * Bit 4 : xg1_request => 1:request single pause frame * Bit 5 : xg1_on_off => 1:request is pause on, 0:off #define netxen_gb_set_gb0_mask(config_word) \1 << 0 )#define netxen_gb_set_gb1_mask(config_word) \1 << 2 )#define netxen_gb_set_gb2_mask(config_word) \1 << 4 )#define netxen_gb_set_gb3_mask(config_word) \1 << 6 )#define netxen_gb_get_gb0_mask(config_word) \0 )#define netxen_gb_get_gb1_mask(config_word) \2 )#define netxen_gb_get_gb2_mask(config_word) \4 )#define netxen_gb_get_gb3_mask(config_word) \6 )#define netxen_gb_unset_gb0_mask(config_word) \1 << 0 ))#define netxen_gb_unset_gb1_mask(config_word) \1 << 2 ))#define netxen_gb_unset_gb2_mask(config_word) \1 << 4 ))#define netxen_gb_unset_gb3_mask(config_word) \1 << 6 ))/* * PHY-Specific MII control/status registers. #define NETXEN_NIU_GB_MII_MGMT_ADDR_CONTROL 0 #define NETXEN_NIU_GB_MII_MGMT_ADDR_STATUS 1 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_ID_0 2 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_ID_1 3 #define NETXEN_NIU_GB_MII_MGMT_ADDR_AUTONEG 4 #define NETXEN_NIU_GB_MII_MGMT_ADDR_LNKPART 5 #define NETXEN_NIU_GB_MII_MGMT_ADDR_AUTONEG_MORE 6 #define NETXEN_NIU_GB_MII_MGMT_ADDR_NEXTPAGE_XMIT 7 #define NETXEN_NIU_GB_MII_MGMT_ADDR_LNKPART_NEXTPAGE 8 #define NETXEN_NIU_GB_MII_MGMT_ADDR_1000BT_CONTROL 9 #define NETXEN_NIU_GB_MII_MGMT_ADDR_1000BT_STATUS 10 #define NETXEN_NIU_GB_MII_MGMT_ADDR_EXTENDED_STATUS 15 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_CONTROL 16 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS 17 #define NETXEN_NIU_GB_MII_MGMT_ADDR_INT_ENABLE 18 #define NETXEN_NIU_GB_MII_MGMT_ADDR_INT_STATUS 19 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_CONTROL_MORE 20 #define NETXEN_NIU_GB_MII_MGMT_ADDR_RECV_ERROR_COUNT 21 #define NETXEN_NIU_GB_MII_MGMT_ADDR_LED_CONTROL 24 #define NETXEN_NIU_GB_MII_MGMT_ADDR_LED_OVERRIDE 25 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_CONTROL_MORE_YET 26 #define NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS_MORE 27 /* * PHY-Specific Status Register (reg 17). * * Bit 0 : jabber => 1:jabber detected, 0:not * Bit 1 : polarity => 1:polarity reversed, 0:normal * Bit 2 : recvpause => 1:receive pause enabled, 0:disabled * Bit 3 : xmitpause => 1:transmit pause enabled, 0:disabled * Bit 4 : energydetect => 1:sleep, 0:active * Bit 5 : downshift => 1:downshift, 0:no downshift * Bit 6 : crossover => 1:MDIX (crossover), 0:MDI (no crossover) * Bits 7-9 : cablelen => not valid in 10Mb/s mode * 0:<50m, 1:50-80m, 2:80-110m, 3:110-140m, 4:>140m * Bit 10 : link => 1:link up, 0:link down * Bit 11 : resolved => 1:speed and duplex resolved, 0:not yet * Bit 12 : pagercvd => 1:page received, 0:page not received * Bit 13 : duplex => 1:full duplex, 0:half duplex * Bits 14-15 : speed => 0:10Mb/s, 1:100Mb/s, 2:1000Mb/s, 3:rsvd #define netxen_get_phy_speed(config_word) (((config_word) >> 14 ) & 0 x03)#define netxen_set_phy_speed(config_word, val) \0 x03) << 14 ))#define netxen_set_phy_duplex(config_word) \1 << 13 )#define netxen_clear_phy_duplex(config_word) \1 << 13 ))#define netxen_get_phy_link(config_word) \10 )#define netxen_get_phy_duplex(config_word) \13 )/* * NIU Mode Register. * Bit 0 : enable FibreChannel * Bit 1 : enable 10/100/1000 Ethernet * Bit 2 : enable 10Gb Ethernet #define netxen_get_niu_enable_ge(config_word) \1 )#define NETXEN_NIU_NON_PROMISC_MODE 0 #define NETXEN_NIU_PROMISC_MODE 1 #define NETXEN_NIU_ALLMULTI_MODE 2 /* * NIU XG MAC Config Register * * Bit 0 : tx_enable => 1:enable frame xmit, 0:disable * Bit 2 : rx_enable => 1:enable frame recv, 0:disable * Bit 4 : soft_reset => 1:reset the MAC , 0:no-op * Bit 27: xaui_framer_reset * Bit 28: xaui_rx_reset * Bit 29: xaui_tx_reset * Bit 30: xg_ingress_afifo_reset * Bit 31: xg_egress_afifo_reset #define netxen_xg_soft_reset(config_word) \1 << 4 )typedef struct {unsigned valid;unsigned start_128M;unsigned end_128M;unsigned start_2M;typedef struct {16 ];#endif /* __NETXEN_NIC_HW_H_ */
Messung V0.5 in Prozent C=96 H=92 G=93
¤ Dauer der Verarbeitung: 0.0 Sekunden
(vorverarbeitet am 2026-06-07)
¤ *© Formatika GbR, Deutschland
