// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2019, The Linux Foundation. All rights reserved.
*/
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
#include <dt-bindings/thermal/thermal.h>
/ {
thermal-zones {
pm6150_thermal: pm6150-thermal {
polling-delay-passive = <100>;
thermal-sensors = <&pm6150_temp>;
trips {
pm6150_trip0: trip0 {
temperature = <95000>;
hysteresis = <0>;
type = "passive";
};
pm6150_crit: crit {
temperature = <115000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pm6150_lsid0: pmic@0 {
compatible = "qcom,pm6150", "qcom,spmi-pmic";
reg = <0x0 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pm6150_pon: pon@800 {
compatible = "qcom,pm8998-pon";
reg = <0x800>;
mode-bootloader = <0x2>;
mode-recovery = <0x1>;
pm6150_pwrkey: pwrkey {
compatible = "qcom,pm8941-pwrkey";
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_POWER>;
};
pm6150_resin: resin {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
status = "disabled";
};
};
pm6150_vbus: usb-vbus-regulator@1100 {
compatible = "qcom,pm6150-vbus-reg",
"qcom,pm8150b-vbus-reg";
reg = <0x1100>;
status = "disabled";
};
pm6150_typec: typec@1500 {
compatible = "qcom,pm6150-typec",
"qcom,pm8150b-typec";
reg = <0x1500>, <0x1700>;
interrupts = <0x0 0x15 0x00 IRQ_TYPE_EDGE_RISING>,
<0x0 0x15 0x01 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x15 0x02 IRQ_TYPE_EDGE_RISING>,
<0x0 0x15 0x03 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x15 0x04 IRQ_TYPE_EDGE_RISING>,
<0x0 0x15 0x05 IRQ_TYPE_EDGE_RISING>,
<0x0 0x15 0x06 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x15 0x07 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x00 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x01 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x02 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x03 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x04 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x05 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x06 IRQ_TYPE_EDGE_RISING>,
<0x0 0x17 0x07 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "or-rid-detect-change",
"vpd-detect",
"cc-state-change",
"vconn-oc",
"vbus-change",
"attach-detach",
"legacy-cable-detect",
"try-snk-src-detect",
"sig-tx",
"sig-rx",
"msg-tx",
"msg-rx",
"msg-tx-failed",
"msg-tx-discarded",
"msg-rx-discarded",
"fr-swap";
status = "disabled";
};
pm6150_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pm6150_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
channel@6 {
reg = <ADC5_DIE_TEMP>;
label = "die_temp";
};
};
pm6150_adc_tm: adc-tm@3500 {
compatible = "qcom,spmi-adc-tm5";
reg = <0x3500>;
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
pm6150_rtc: rtc@6000 {
compatible = "qcom,pm8941-rtc";
reg = <0x6000>, <0x6100>;
reg-names = "rtc", "alarm";
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
};
pm6150_gpios: gpio@c000 {
compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
gpio-controller;
gpio-ranges = <&pm6150_gpios 0 0 10>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pm6150_lsid1: pmic@1 {
compatible = "qcom,pm6150", "qcom,spmi-pmic";
reg = <0x1 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pm6150_vib: vibrator@5300 {
compatible = "qcom,pm6150-vib", "qcom,pmi632-vib";
reg = <0x5300>;
status = "disabled";
};
};
};
