Quellcodebibliothek Statistik Leitseite products/Sources/formale Sprachen/C/Linux/arch/arm64/boot/dts/freescale/   (Open Source Betriebssystem Version 6.17.9©)  Datei vom 24.10.2025 mit Größe 9 kB image not shown  

Quelle  imx8mp-venice-gw72xx.dtsi   Sprache: unbekannt

 
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright 2023 Gateworks Corporation
 */

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/phy/phy-imx8-pcie.h>

/ {
 aliases {
  ethernet1 = ð1;
 };

 connector {
  compatible = "gpio-usb-b-connector", "usb-b-connector";
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_usbcon1>;
  type = "micro";
  label = "otg";
  vbus-supply = <®_usb1_vbus>;
  id-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;

  port {
   usb_dr_connector: endpoint {
    remote-endpoint = <&usb3_dwc>;
   };
  };
 };

 led-controller {
  compatible = "gpio-leds";
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_gpio_leds>;

  led-0 {
   function = LED_FUNCTION_STATUS;
   color = <LED_COLOR_ID_GREEN>;
   gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
   default-state = "on";
   linux,default-trigger = "heartbeat";
  };

  led-1 {
   function = LED_FUNCTION_STATUS;
   color = <LED_COLOR_ID_RED>;
   gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
   default-state = "off";
  };
 };

 pcie0_refclk: clock-pcie0 {
  compatible = "fixed-clock";
  #clock-cells = <0>;
  clock-frequency = <100000000>;
 };

 pps {
  compatible = "pps-gpio";
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_pps>;
  gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
  status = "okay";
 };

 reg_usb1_vbus: regulator-usb1 {
  compatible = "regulator-fixed";
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_reg_usb1_en>;
  regulator-name = "usb1_vbus";
  gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
  enable-active-high;
  regulator-min-microvolt = <5000000>;
  regulator-max-microvolt = <5000000>;
 };

 reg_usb2_vbus: regulator-usb2 {
  compatible = "regulator-fixed";
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_reg_usb2_en>;
  regulator-name = "usb2_vbus";
  gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
  enable-active-high;
  regulator-min-microvolt = <5000000>;
  regulator-max-microvolt = <5000000>;
 };

 reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
  compatible = "regulator-fixed";
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_usdhc2_vmmc>;
  regulator-name = "VDD_3V3_SD";
  enable-active-high;
  gpio = <&gpio2 19 0>; /* SD2_RESET */
  off-on-delay-us = <12000>;
  regulator-max-microvolt = <3300000>;
  regulator-min-microvolt = <3300000>;
  startup-delay-us = <100>;
 };
};

/* off-board header */
&ecspi2 {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_spi2>;
 cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>,
     <&gpio1 10 GPIO_ACTIVE_LOW>;
 status = "okay";

 tpm@1 {
  compatible = "atmel,attpm20p", "tcg,tpm_tis-spi";
  reg = <0x1>;
  spi-max-frequency = <25000000>;
 };
};

&gpio4 {
 gpio-line-names =
  "", "", "", "",
  "", "", "", "",
  "dio1", "", "", "dio0",
  "", "", "pci_usb_sel", "",
  "", "", "", "",
  "", "", "rs485_en", "rs485_term",
  "", "", "", "rs485_half",
  "pci_wdis#", "", "", "";
};

&i2c2 {
 clock-frequency = <400000>;
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_i2c2>;
 status = "okay";

 accelerometer@19 {
  compatible = "st,lis2de12";
  reg = <0x19>;
  pinctrl-names = "default";
  pinctrl-0 = <&pinctrl_accel>;
  st,drdy-int-pin = <1>;
  interrupt-parent = <&gpio4>;
  interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
 };
};

&pcie_phy {
 fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
 fsl,clkreq-unsupported;
 clocks = <&pcie0_refclk>;
 clock-names = "ref";
 status = "okay";
};

&pcie {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_pcie0>;
 reset-gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
 status = "okay";

 pcie@0,0 {
  reg = <0x0000 0 0 0 0>;
  device_type = "pci";
  #address-cells = <3>;
  #size-cells = <2>;
  ranges;

  pcie@0,0 {
   reg = <0x0000 0 0 0 0>;
   device_type = "pci";
   #address-cells = <3>;
   #size-cells = <2>;
   ranges;

   pcie@3,0 {
    reg = <0x1800 0 0 0 0>;
    device_type = "pci";
    #address-cells = <3>;
    #size-cells = <2>;
    ranges;

    eth1: ethernet@0,0 {
     reg = <0x0000 0 0 0 0>;
     #address-cells = <3>;
     #size-cells = <2>;
     ranges;
     local-mac-address = [00 00 00 00 00 00];
    };
   };
  };
 };
};

/* GPS */
&uart1 {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_uart1>;
 status = "okay";
};

/* off-board header */
&uart3 {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_uart3>;
 status = "okay";
};

/* RS232 */
&uart4 {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_uart4>;
 status = "okay";
};

/* USB1 - OTG */
&usb3_0 {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_usb1>;
 fsl,over-current-active-low;
 status = "okay";
};

&usb3_phy0 {
 status = "okay";
};

&usb_dwc3_0 {
 /* dual role is implemented but not a full featured OTG */
 adp-disable;
 hnp-disable;
 srp-disable;
 dr_mode = "otg";
 usb-role-switch;
 role-switch-default-mode = "peripheral";
 status = "okay";

 port {
  usb3_dwc: endpoint {
   remote-endpoint = <&usb_dr_connector>;
  };
 };
};

/* USB2 - USB3.0 Hub */
&usb3_1 {
 fsl,permanently-attached;
 fsl,disable-port-power-control;
 status = "okay";
};

&usb3_phy1 {
 vbus-supply = <®_usb2_vbus>;
 status = "okay";
};

&usb_dwc3_1 {
 dr_mode = "host";
 status = "okay";
};

/* microSD */
&usdhc2 {
 pinctrl-names = "default", "state_100mhz", "state_200mhz";
 pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
 pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
 pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
 cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 bus-width = <4>;
 vmmc-supply = <®_usdhc2_vmmc>;
 status = "okay";
};

&iomuxc {
 pinctrl-names = "default";
 pinctrl-0 = <&pinctrl_hog>;

 pinctrl_hog: hoggrp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI1_RXD6__GPIO4_IO08 0x40000146 /* DIO1 */
   MX8MP_IOMUXC_SAI1_TXC__GPIO4_IO11 0x40000146 /* DIO0 */
   MX8MP_IOMUXC_SAI1_TXD2__GPIO4_IO14 0x40000106 /* PCIE_USBSEL */
   MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27 0x40000106 /* RS485_HALF */
   MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x40000106 /* RS485_EN */
   MX8MP_IOMUXC_SAI2_RXD0__GPIO4_IO23 0x40000106 /* RS485_TERM */
   MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x40000106 /* PCIE_WDIS# */
  >;
 };

 pinctrl_accel: accelgrp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x150 /* IRQ */
  >;
 };

 pinctrl_gpio_leds: gpioledgrp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01 0x6 /* LEDG */
   MX8MP_IOMUXC_SAI1_RXD3__GPIO4_IO05 0x6 /* LEDR */
  >;
 };

 pinctrl_pcie0: pcie0grp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x106
  >;
 };

 pinctrl_pps: ppsgrp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x146
  >;
 };

 pinctrl_reg_usb1_en: regusb1grp {
  fsl,pins = <
   MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12 0x146 /* USB1_EN */
  >;
 };

 pinctrl_usb1: usb1grp {
  fsl,pins = <
   MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC 0x140 /* USB1_FLT# */
  >;
 };

 pinctrl_usbcon1: usbcon1grp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21 0x140 /* USB1_ID */
  >;
 };

 pinctrl_reg_usb2_en: regusb2grp {
  fsl,pins = <
   MX8MP_IOMUXC_SAI1_TXD0__GPIO4_IO12 0x146 /* USBHUB_RST# */
  >;
 };

 pinctrl_spi2: spi2grp {
  fsl,pins = <
   MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x140
   MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x140
   MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x140
   MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x140
   MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x140
  >;
 };

 pinctrl_uart1: uart1grp {
  fsl,pins = <
   MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140
   MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140
  >;
 };

 pinctrl_uart3: uart3grp {
  fsl,pins = <
   MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x140
   MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x140
  >;
 };

 pinctrl_uart4: uart4grp {
  fsl,pins = <
   MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x140
   MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x140
  >;
 };

 pinctrl_usdhc1: usdhc1grp {
  fsl,pins = <
   MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x190
   MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d0
   MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d0
   MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d0
   MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d0
   MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d0
  >;
 };

 pinctrl_usdhc2: usdhc2grp {
  fsl,pins = <
   MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
   MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
   MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
   MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
   MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
   MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
   MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
  >;
 };

 pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
  fsl,pins = <
   MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
   MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
   MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
   MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
   MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
   MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
   MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
  >;
 };

 pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
  fsl,pins = <
   MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
   MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
   MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
   MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
   MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
   MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
   MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
  >;
 };

 pinctrl_usdhc2_vmmc: usdhc2-vmmc-grp {
  fsl,pins = <
   MX8MP_IOMUXC_SD2_RESET_B__USDHC2_RESET_B 0x1d0
  >;
 };

 pinctrl_usdhc2_gpio: usdhc2gpiogrp {
  fsl,pins = <
   MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12  0x1c4
  >;
 };
};

[ Dauer der Verarbeitung: 0.2 Sekunden  (vorverarbeitet)  ]