// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2011-2013 Texas Instruments Incorporated -
https://www.ti.com/
*/
#include <dt-bindings/input/input.h>
#include "elpida_ecb240abacn.dtsi"
#include "omap4-mcpdm.dtsi"
/ {
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
dsp_memory_region: dsp-memory@98000000 {
compatible = "shared-dma-pool";
reg = <0x98000000 0x800000>;
reusable;
status = "okay";
};
ipu_memory_region: ipu-memory@98800000 {
compatible = "shared-dma-pool";
reg = <0x98800000 0x7000000>;
reusable;
status = "okay";
};
};
chosen {
stdout-path = &uart3;
};
aliases {
display0 = &dvi0;
display1 = &hdmi0;
ethernet = ðernet;
};
leds: leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <
&led_wkgpio_pins
>;
led-heartbeat {
label = "pandaboard::status1";
gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-mmc {
label = "pandaboard::status2";
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
};
};
gpio_keys: gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <
&button_pins
>;
buttonS2 {
label = "button S2";
gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; /* gpio_121 */
linux,code = <BTN_0>;
wakeup-source;
};
};
sound: sound {
compatible = "ti,abe-twl6040";
ti,model = "PandaBoard";
ti,mclk-freq = <38400000>;
ti,mcpdm = <&mcpdm>;
ti,twl6040 = <&twl6040>;
/* Audio routing */
ti,audio-routing =
"Headset Stereophone", "HSOL",
"Headset Stereophone", "HSOR",
"Ext Spk", "HFL",
"Ext Spk", "HFR",
"Line Out", "AUXL",
"Line Out", "AUXR",
"HSMIC", "Headset Mic",
"Headset Mic", "Headset Mic Bias",
"AFML", "Line In",
"AFMR", "Line In";
};
/* HS USB Port 1 Power */
hsusb1_power: hsusb1_power_reg {
compatible = "regulator-fixed";
regulator-name = "hsusb1_vbus";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */
startup-delay-us = <70000>;
enable-active-high;
/*
* boot-on is required along with always-on as the
* regulator framework doesn't enable the regulator
* if boot-on is not there.
*/
regulator-always-on;
regulator-boot-on;
};
/* HS USB Host PHY on PORT 1 */
hsusb1_phy: hsusb1_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
#phy-cells = <0>;
vcc-supply = <&hsusb1_power>;
clocks = <&auxclk3_ck>;
clock-names = "main_clk";
clock-frequency = <19200000>;
};
wl12xx_pwrseq: wl12xx-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&twl 0>;
clock-names = "ext_clock";
};
/* regulator for wl12xx on sdio5 */
wl12xx_vmmc: wl12xx_vmmc {
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_gpio>;
compatible = "regulator-fixed";
regulator-name = "vwl1271";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
startup-delay-us = <70000>;
enable-active-high;
};
tfp410: encoder0 {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tfp410_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
dvi0: connector0 {
compatible = "dvi-connector";
label = "dvi";
digital;
ddc-i2c-bus = <&i2c3>;
port {
dvi_connector_in: endpoint {
remote-endpoint = <&tfp410_out>;
};
};
};
tpd12s015: encoder1 {
compatible = "ti,tpd12s015";
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
<&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
<&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tpd12s015_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
port@1 {
reg = <1>;
tpd12s015_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
};
};
hdmi0: connector1 {
compatible = "hdmi-connector";
label = "hdmi";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&tpd12s015_out>;
};
};
};
};
&omap4_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&dss_dpi_pins
&tfp410_pins
&dss_hdmi_pins
&tpd12s015_pins
&hsusbb1_pins
>;
twl6040_pins: twl6040-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
>;
};
mcbsp1_pins: mcbsp1-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
>;
};
dss_dpi_pins: dss-dpi-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
>;
};
tfp410_pins: tfp410-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */
>;
};
dss_hdmi_pins: dss-hdmi-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
};
tpd12s015_pins: tpd12s015-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
>;
};
hsusbb1_pins: hsusbb1-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy
_clk */
OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
>;
};
i2c1_pins: i2c1-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
>;
};
i2c2_pins: i2c2-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: i2c3-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
>;
};
i2c4_pins: i2c4-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
>;
};
/*
* wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
* REVISIT: Are the pull-ups needed for GPIO 48 and 49?
*/
wl12xx_gpio: wl12xx-gpio-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 - WLAN_EN */
OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
>;
};
/* wl12xx GPIO inputs and SDIO pins */
wl12xx_pins: wl12xx-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
>;
};
button_pins: button-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_121 */
>;
};
bt_pins: bt-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 - BTEN */
OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 - BTWAKEUP */
>;
};
uart2_pins: uart2-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts - HCI */
OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */
OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */
OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
>;
};
};
&omap4_pmx_wkup {
led_wkgpio_pins: leds-wkpins-pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
twl: twl@48 {
reg = <0x48>;
/* IRQ# = 7 */
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
#clock-cells = <1>;
system-power-controller;
};
twl6040: twl@4b {
compatible = "ti,twl6040";
#clock-cells = <0>;
reg = <0x4b>;
pinctrl-names = "default";
pinctrl-0 = <&twl6040_pins>;
/* IRQ# = 119 */
interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
vio-supply = <&v1v8>;
v2v1-supply = <&v2v1>;
enable-active-high;
};
};
#include "twl6030.dtsi"
#include "twl6030_omap4.dtsi"
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
clock-frequency = <400000>;
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <100000>;
/*
* Display monitor features are burnt in their EEPROM as EDID data.
* The EEPROM is connected as I2C slave device.
*/
eeprom@50 {
compatible = "ti,eeprom";
reg = <0x50>;
};
};
&i2c4 {
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins>;
clock-frequency = <400000>;
};
&mmc1 {
vmmc-supply = <&vmmc>;
bus-width = <8>;
};
&mmc2 {
status = "disabled";
};
&mmc3 {
status = "disabled";
};
&mmc4 {
status = "disabled";
};
&mmc5 {
pinctrl-names = "default";
pinctrl-0 = <&wl12xx_pins>;
vmmc-supply = <&wl12xx_vmmc>;
interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core 0x10e>;
non-removable;
bus-width = <4>;
cap-power-off-card;
mmc-pwrseq = <&wl12xx_pwrseq>;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1271";
reg = <2>;
/* gpio_53 with gpmc_ncs3 pad as wakeup */
interrupts-extended = <&gpio2 21 IRQ_TYPE_LEVEL_HIGH>,
<&omap4_pmx_core 0x3a>;
interrupt-names = "irq", "wakeup";
ref-clock-frequency = <38400000>;
};
};
&emif1 {
cs1-used;
device-handle = <&elpida_ECB240ABACN>;
};
&emif2 {
cs1-used;
device-handle = <&elpida_ECB240ABACN>;
};
&mcbsp1 {
pinctrl-names = "default";
pinctrl-0 = <&mcbsp1_pins>;
status = "okay";
};
&twl_usb_comparator {
usb-supply = <&vusb>;
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART2_RX>;
bluetooth {
compatible = "ti,wl1271-st";
pinctrl-names = "default";
pinctrl-0 = <&bt_pins>;
enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>; /* GPIO_46 */
clocks = <&twl 0>;
clock-names = "ext_clock";
};
};
&uart3 {
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART3_RX>;
};
&uart4 {
interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART4_RX>;
};
&usb_otg_hs {
interface-type = <1>;
mode = <3>;
power = <50>;
};
&usbhshost {
port1-mode = "ehci-phy";
};
&usbhsehci {
phys = <&hsusb1_phy>;
#address-cells = <1>;
#size-cells = <0>;
hub@1 {
compatible = "usb424,9514";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
ethernet: ethernet@1 {
compatible = "usb424,ec00";
reg = <1>;
};
};
};
&dss {
status = "okay";
port {
dpi_out: endpoint {
remote-endpoint = <&tfp410_in>;
data-lines = <24>;
};
};
};
&dsi2 {
status = "okay";
vdd-supply = <&vcxio>;
};
&hdmi {
status = "okay";
vdda-supply = <&vdac>;
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
};
};
};
&dsp {
status = "okay";
memory-region = <&dsp_memory_region>;
ti,timers = <&timer5>;
ti,watchdog-timers = <&timer6>;
};
&ipu {
status = "okay";
memory-region = <&ipu_memory_region>;
ti,timers = <&timer3>;
ti,watchdog-timers = <&timer9>, <&timer11>;
};
