// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2021, AngeloGioacchino Del Regno
* <angelogioacchino.delregno@somainline.org>
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include "msm8998.dtsi"
#include "pm8005.dtsi"
#include "pm8998.dtsi"
#include "pmi8998.dtsi"
/ {
model = "F(x)tec Pro1 (QX1000)";
compatible = "fxtec,pro1", "qcom,msm8998";
chassis-type = "handset";
qcom,board-id = <0x02000b 0x10>;
aliases {
serial0 = &blsp2_uart1;
serial1 = &blsp1_uart3;
};
/*
* Until we hook up type-c detection, we
* have to stick with this. But it works.
*/
extcon_usb: extcon-usb {
compatible = "linux,extcon-usb-gpio";
id-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
};
gpio-hall-sensors {
compatible = "gpio-keys";
label = "Hall sensors";
pinctrl-names = "default";
pinctrl-0 = <&hall_sensor1_default>;
event-hall-sensor1 {
label = "Keyboard Hall Sensor";
gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>;
debounce-interval = <15>;
wakeup-source;
linux,input-type = <EV_SW>;
linux,code = <SW_KEYPAD_SLIDE>;
};
};
gpio-kb-extra-keys {
compatible = "gpio-keys";
label = "Keyboard extra keys";
pinctrl-names = "default";
pinctrl-0 = <&gpio_kb_pins_extra>;
key-home {
label = "Home";
gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
linux,code = <KEY_HOMEPAGE>;
debounce-interval = <15>;
linux,can-disable;
};
key-super-l {
label = "Super Left";
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
linux,code = <KEY_FN>;
debounce-interval = <15>;
linux,can-disable;
};
key-super-r {
label = "Super Right";
gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
linux,code = <KEY_FN>;
debounce-interval = <15>;
linux,can-disable;
};
key-shift {
label = "Shift";
gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RIGHTSHIFT>;
debounce-interval = <15>;
linux,can-disable;
};
key-ctrl {
label = "Ctrl";
gpios = <&tlmm 128 GPIO_ACTIVE_LOW>;
linux,code = <KEY_LEFTCTRL>;
debounce-interval = <15>;
linux,can-disable;
};
key-alt {
label = "Alt";
gpios = <&tlmm 129 GPIO_ACTIVE_LOW>;
linux,code = <KEY_LEFTALT>;
debounce-interval = <15>;
linux,can-disable;
};
};
gpio-keys {
compatible = "gpio-keys";
label = "Side buttons";
pinctrl-names = "default";
pinctrl-0 = <&vol_up_pin_a>, <&cam_focus_pin_a>,
<&cam_snapshot_pin_a>;
button-vol-up {
label = "Volume Up";
gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
linux,input-type = <EV_KEY>;
linux,code = <KEY_VOLUMEUP>;
wakeup-source;
debounce-interval = <15>;
};
button-camera-snapshot {
label = "Camera Snapshot";
gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>;
linux,input-type = <EV_KEY>;
linux,code = <KEY_CAMERA>;
debounce-interval = <15>;
};
button-camera-focus {
label = "Camera Focus";
gpios = <&pm8998_gpios 8 GPIO_ACTIVE_LOW>;
linux,input-type = <EV_KEY>;
linux,code = <KEY_CAMERA_FOCUS>;
debounce-interval = <15>;
};
};
keyboard-leds {
compatible = "gpio-leds";
led-0 {
color = <LED_COLOR_ID_WHITE>;
default-state = "off";
function = LED_FUNCTION_KBD_BACKLIGHT;
gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
label = "white:kbd_backlight";
retain-state-suspended;
};
led-1 {
color = <LED_COLOR_ID_YELLOW>;
default-state = "off";
function = LED_FUNCTION_CAPSLOCK;
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
label = "yellow:capslock";
linux,default-trigger = "kbd-capslock";
};
};
reserved-memory {
cont_splash_mem: memory@9d400000 {
reg = <0x0 0x9d400000 0x0 0x2000000>;
no-map;
};
zap_shader_region: memory@f6400000 {
compatible = "shared-dma-pool";
reg = <0x0 0xf6400000 0x0 0x2000>;
no-map;
};
ramoops@ffc00000 {
compatible = "ramoops";
reg = <0x0 0xffc00000 0x0 0x100000>;
console-size = <0x60000>;
ecc-size = <16>;
ftrace-size = <0x10000>;
pmsg-size = <0x20000>;
record-size = <0x10000>;
};
};
ts_vio_vreg: ts-vio-vreg {
compatible = "regulator-fixed";
regulator-name = "ts_vio_reg";
startup-delay-us = <2>;
enable-active-high;
gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&ts_vio_default>;
regulator-always-on;
};
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
regulator-always-on;
regulator-boot-on;
};
};
&blsp1_uart3 {
status = "okay";
bluetooth {
compatible = "qcom,wcn3990-bt";
vddio-supply = <&vreg_s4a_1p8>;
vddxo-supply = <&vreg_l7a_1p8>;
vddrf-supply = <&vreg_l17a_1p3>;
vddch0-supply = <&vreg_l25a_3p3>;
max-speed = <3200000>;
};
};
&blsp1_uart3_on {
rx-pins {
/delete-property/ bias-disable;
/*
* Configure a pull-up on 45 (RX). This is needed to
* avoid garbage data when the TX pin of the Bluetooth
* module is in tri-state (module powered off or not
* driving the signal yet).
*/
bias-pull-up;
};
cts-pins {
/delete-property/ bias-disable;
/*
* Configure a pull-down on 47 (CTS) to match the pull
* of the Bluetooth module.
*/
bias-pull-down;
};
};
&blsp2_uart1 {
status = "okay";
};
&blsp2_i2c1 {
status = "okay";
touchscreen@14 {
compatible = "goodix,gt9286";
reg = <0x14>;
interrupt-parent = <&tlmm>;
interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
AVDD28-supply = <&vreg_l28_3p0>;
VDDIO-supply = <&ts_vio_vreg>;
pinctrl-names = "active";
pinctrl-0 = <&ts_rst_n>, <&ts_int_n>;
};
};
&etf {
status = "okay";
};
&etm1 {
status = "okay";
};
&etm2 {
status = "okay";
};
&etm3 {
status = "okay";
};
&etm4 {
status = "okay";
};
&etm5 {
status = "okay";
};
&etm6 {
status = "okay";
};
&etm7 {
status = "okay";
};
&etm8 {
status = "okay";
};
&etr {
status = "okay";
};
&funnel1 {
status = "okay";
};
&funnel2 {
status = "okay";
};
&funnel3 {
status = "okay";
};
&funnel4 {
/* FIXME: Figure out why clock late_initcall crashes the board with this enabled. */
};
&funnel5 {
/* FIXME: Figure out why clock late_initcall crashes the board with this enabled. */
};
&pcie0 {
status = "okay";
};
&pcie_phy {
status = "okay";
};
&pm8005_regulators {
vdd_s1-supply = <&vph_pwr>;
pm8005_s1: s1 { /* VDD_GFX supply */
regulator-min-microvolt = <524000>;
regulator-max-microvolt = <1100000>;
regulator-enable-ramp-delay = <500>;
/* Hack until we rig up the gpu consumer */
regulator-always-on;
};
};
&pm8998_gpios {
vol_up_pin_a: vol-up-active-state {
pins = "gpio6";
function = "normal";
bias-pull-up;
input-enable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
cam_focus_pin_a: cam-focus-btn-active-state {
pins = "gpio7";
function = "normal";
bias-pull-up;
input-enable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
cam_snapshot_pin_a: cam-snapshot-btn-active-state {
pins = "gpio8";
function = "normal";
bias-pull-up;
input-enable;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
};
&pm8998_resin {
linux,code = <KEY_VOLUMEDOWN>;
status = "okay";
};
&qusb2phy {
status = "okay";
vdd-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l12a_1p8>;
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
};
&replicator1 {
status = "okay";
};
&rpm_requests {
regulators-0 {
compatible = "qcom,rpm-pm8998-regulators";
vdd_s1-supply = <&vph_pwr>;
vdd_s2-supply = <&vph_pwr>;
vdd_s3-supply = <&vph_pwr>;
vdd_s4-supply = <&vph_pwr>;
vdd_s5-supply = <&vph_pwr>;
vdd_s6-supply = <&vph_pwr>;
vdd_s7-supply = <&vph_pwr>;
vdd_s8-supply = <&vph_pwr>;
vdd_s9-supply = <&vph_pwr>;
vdd_s10-supply = <&vph_pwr>;
vdd_s11-supply = <&vph_pwr>;
vdd_s12-supply = <&vph_pwr>;
vdd_s13-supply = <&vph_pwr>;
vdd_l1_l27-supply = <&vreg_s7a_1p025>;
vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
vdd_l3_l11-supply = <&vreg_s7a_1p025>;
vdd_l4_l5-supply = <&vreg_s7a_1p025>;
vdd_l6-supply = <&vreg_s5a_2p04>;
vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
vdd_l9-supply = <&vreg_bob>;
vdd_l10_l23_l25-supply = <&vreg_bob>;
vdd_l13_l19_l21-supply = <&vreg_bob>;
vdd_l16_l28-supply = <&vreg_bob>;
vdd_l18_l22-supply = <&vreg_bob>;
vdd_l20_l24-supply = <&vreg_bob>;
vdd_l26-supply = <&vreg_s3a_1p35>;
vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
vreg_s3a_1p35: s3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
vreg_s4a_1p8: s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-allow-set-load;
};
vreg_s5a_2p04: s5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
vreg_s7a_1p025: s7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
vreg_l1a_0p875: l1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
};
vreg_l2a_1p2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
vreg_l3a_1p0: l3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
vreg_l5a_0p8: l5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
};
vreg_l6a_1p8: l6 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <1808000>;
};
vreg_l7a_1p8: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vreg_l8a_1p2: l8 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
vreg_l9a_1p8: l9 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
vreg_l10a_1p8: l10 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
vreg_l11a_1p0: l11 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
vreg_l12a_1p8: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vreg_l13a_2p95: l13 {
regulator-min-microvolt = <1808000>;
regulator-max-microvolt = <2960000>;
};
vreg_l14a_1p88: l14 {
regulator-min-microvolt = <1880000>;
regulator-max-microvolt = <1880000>;
};
vreg_l15a_1p8: l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vreg_l16a_2p7: l16 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
vreg_l17a_1p3: l17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
};
vreg_l18a_2p7: l18 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
};
vreg_l19a_3p0: l19 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
};
vreg_l20a_2p95: l20 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
regulator-allow-set-load;
};
vreg_l21a_2p95: l21 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2960000>;
regulator-system-load = <800000>;
regulator-allow-set-load;
};
vreg_l22a_2p85: l22 {
regulator-min-microvolt = <2864000>;
regulator-max-microvolt = <2864000>;
};
vreg_l23a_3p3: l23 {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3312000>;
};
vreg_l24a_3p075: l24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
};
vreg_l25a_3p3: l25 {
regulator-min-microvolt = <3104000>;
regulator-max-microvolt = <3312000>;
};
vreg_l26a_1p2: l26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-allow-set-load;
};
vreg_l28_3p0: l28 {
regulator-min-microvolt = <3008000>;
regulator-max-microvolt = <3008000>;
};
vreg_lvs1a_1p8: lvs1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vreg_lvs2a_1p8: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
regulators-1 {
compatible = "qcom,rpm-pmi8998-regulators";
vdd_bob-supply = <&vph_pwr>;
vreg_bob: bob {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3600000>;
};
};
};
&remoteproc_adsp {
status = "okay";
};
&remoteproc_mss {
status = "okay";
};
&remoteproc_slpi {
status = "okay";
};
&tlmm {
gpio-reserved-ranges = <0 4>;
mdp_vsync_n: mdp-vsync-n-state {
pins = "gpio10";
function = "mdp_vsync_a";
bias-pull-down;
drive-strength = <2>;
};
gpio_kb_pins_extra: gpio-kb-pins-extra-state {
pins = "gpio21", "gpio32", "gpio33", "gpio114",
"gpio128", "gpio129";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
ts_vio_default: ts-vio-def-state {
pins = "gpio81";
function = "gpio";
bias-disable;
drive-strength = <2>;
};
ts_rst_n: ts-rst-n-state {
pins = "gpio89";
function = "gpio";
bias-pull-up;
drive-strength = <8>;
};
hall_sensor1_default: hall-sensor1-def-state {
pins = "gpio124";
function = "gpio";
bias-disable;
drive-strength = <2>;
};
ts_int_n: ts-int-n-state {
pins = "gpio125";
function = "gpio";
bias-disable;
drive-strength = <8>;
};
};
&sdhc2 {
status = "okay";
cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vreg_l21a_2p95>;
vqmmc-supply = <&vreg_l13a_2p95>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_on &sdc2_cd>;
pinctrl-1 = <&sdc2_off &sdc2_cd>;
};
&stm {
status = "okay";
};
&ufshc {
status = "okay";
vcc-supply = <&vreg_l20a_2p95>;
vccq-supply = <&vreg_l26a_1p2>;
vccq2-supply = <&vreg_s4a_1p8>;
vdd-hba-supply = <&vreg_l26a_1p2>;
vcc-max-microamp = <750000>;
vccq-max-microamp = <560000>;
vccq2-max-microamp = <750000>;
};
&ufsphy {
status = "okay";
vdda-phy-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l2a_1p2>;
};
&usb3 {
status = "okay";
};
&usb3_dwc3 {
dr_mode = "peripheral";
extcon = <&extcon_usb>;
};
&usb3phy {
status = "okay";
vdda-phy-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l2a_1p2>;
};
/* GT9286 analog supply */
&vreg_l28_3p0 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
&wifi {
status = "okay";
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
};
