// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (c) 2022, Collabora Ltd
* Author: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "mt6795.dtsi"
#include "mt6331.dtsi"
/ {
model = "Sony Xperia M5";
compatible = "sony,xperia-m5", "mediatek,mt6795";
chassis-type = "handset";
aliases {
mmc0 = &mmc0;
mmc1 = &mmc1;
mmc2 = &mmc2;
serial0 = &uart0;
serial1 = &uart1;
};
backlight_lcd0: backlight {
compatible = "led-backlight";
leds = <&disp_led_pwm>, <&pmic_bl_led>;
default-brightness-level = <300>;
};
led-controller-display {
compatible = "pwm-leds";
disp_led_pwm: led-0 {
label = "backlight-pwm";
pwms = <&pwm0 0 500000>;
max-brightness = <1024>;
};
};
memory@40000000 {
device_type = "memory";
reg = <0 0x40000000 0 0x1e800000>;
};
reserved_memory: reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
/* 128 KiB reserved for ARM Trusted Firmware (BL31) */
bl31_secmon_reserved: secmon@43000000 {
reg = <0 0x43000000 0 0x30000>;
no-map;
};
/* preloader and bootloader regions cannot be touched */
preloader-region@44800000 {
reg = <0 0x44800000 0 0x100000>;
no-map;
};
bootloader-region@46000000 {
reg = <0 0x46000000 0 0x400000>;
no-map;
};
};
vreg_disp_avdd: regulator-disp-avdd {
compatible = "regulator-fixed";
regulator-name = "disp_avdd";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&pio 138 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vreg_disp_avee: regulator-disp-avee {
compatible = "regulator-fixed";
regulator-name = "disp_avee";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&pio 139 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vreg_disp_vddh: regulator-disp-vddh {
compatible = "regulator-fixed";
regulator-name = "disp_vddh";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
};
&dsi0 {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
panel: panel@0 {
compatible = "sharp,ls060t1sx01";
reg = <0>;
avdd-supply = <&vreg_disp_avdd>;
avee-supply = <&vreg_disp_avee>;
vddi-supply = <&mt6331_vgp3_reg>;
vddh-supply = <&vreg_disp_vddh>;
reset-gpios = <&pio 106 GPIO_ACTIVE_LOW>;
backlight = <&backlight_lcd0>;
pinctrl-0 = <&disp_rst_pins>;
pinctrl-names = "default";
port {
panel_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
};
port {
dsi0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
&fhctl {
clocks = <&apmixedsys CLK_APMIXED_MAINPLL>, <&apmixedsys CLK_APMIXED_MPLL>,
<&apmixedsys CLK_APMIXED_MSDCPLL>;
mediatek,hopping-ssc-percent = <8>, <5>, <8>;
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "okay";
accelerometer@10 {
compatible = "bosch,bma255";
reg = <0x10>;
pinctrl-names = "default";
pinctrl-0 = <&accel_pins>;
};
magnetometer@12 {
compatible = "bosch,bmm150";
reg = <0x12>;
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "okay";
touchscreen@20 {
compatible = "syna,rmi4-i2c";
reg = <0x20>;
#address-cells = <1>;
#size-cells = <0>;
interrupts-extended = <&pio 6 IRQ_TYPE_EDGE_FALLING>;
pinctrl-names = "default";
pinctrl-0 = <&ts_pins>;
syna,startup-delay-ms = <160>;
syna,reset-delay-ms = <90>;
rmi4-f01@1 {
reg = <0x1>;
syna,nosleep-mode = <1>;
};
rmi4-f12@12 {
reg = <0x12>;
syna,sensor-type = <1>;
};
};
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
status = "okay";
pn547: nfc@28 {
compatible = "nxp,pn544-i2c";
reg = <0x28>;
interrupts-extended = <&pio 3 IRQ_TYPE_EDGE_RISING>;
pinctrl-names = "default";
pinctrl-0 = <&nfc_pins>;
enable-gpios = <&pio 149 GPIO_ACTIVE_HIGH>;
firmware-gpios = <&pio 94 GPIO_ACTIVE_HIGH>;
};
proximity@48 {
compatible = "sensortek,stk3310";
reg = <0x48>;
interrupts-extended = <&pio 8 IRQ_TYPE_EDGE_FALLING>;
pinctrl-names = "default";
pinctrl-0 = <&proximity_pins>;
};
};
&mmc0 {
/* eMMC controller */
mediatek,latch-ck = <4>; /* hs400 */
mediatek,hs200-cmd-int-delay = <1>;
mediatek,hs400-cmd-int-delay = <1>;
mediatek,hs400-ds-dly3 = <0x1a>;
non-removable;
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&mmc0_pins_default>;
pinctrl-1 = <&mmc0_pins_uhs>;
vmmc-supply = <&mt6331_vemc33_reg>;
vqmmc-supply = <&mt6331_vio18_reg>;
status = "okay";
};
&mmc1 {
/* MicroSD card slot */
vmmc-supply = <&mt6331_vmc_reg>;
vqmmc-supply = <&mt6331_vmch_reg>;
status = "okay";
};
&mmc2 {
/* SDIO WiFi on MMC2 */
vmmc-supply = <&mt6331_vmc_reg>;
vqmmc-supply = <&mt6331_vmch_reg>;
status = "okay";
};
&mt6331_vgp3_reg {
regulator-min-microvolt = <1800000>;
};
&pio {
disp_rst_pins: lcm-pins {
pins-rst {
pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
};
};
mmc0_pins_default: emmc-sdr-pins {
pins-cmd-dat {
pinmux = <PINMUX_GPIO154__FUNC_MSDC0_DAT0>,
<PINMUX_GPIO155__FUNC_MSDC0_DAT1>,
<PINMUX_GPIO156__FUNC_MSDC0_DAT2>,
<PINMUX_GPIO157__FUNC_MSDC0_DAT3>,
<PINMUX_GPIO158__FUNC_MSDC0_DAT4>,
<PINMUX_GPIO159__FUNC_MSDC0_DAT5>,
<PINMUX_GPIO160__FUNC_MSDC0_DAT6>,
<PINMUX_GPIO161__FUNC_MSDC0_DAT7>,
<PINMUX_GPIO162__FUNC_MSDC0_CMD>;
input-enable;
bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
};
pins-clk {
pinmux = <PINMUX_GPIO163__FUNC_MSDC0_CLK>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
};
pins-rst {
pinmux = <PINMUX_GPIO165__FUNC_MSDC0_RSTB>;
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
};
};
mmc0_pins_uhs: emmc-uhs-pins {
pins-cmd-dat {
pinmux = <PINMUX_GPIO154__FUNC_MSDC0_DAT0>,
<PINMUX_GPIO155__FUNC_MSDC0_DAT1>,
<PINMUX_GPIO156__FUNC_MSDC0_DAT2>,
<PINMUX_GPIO157__FUNC_MSDC0_DAT3>,
<PINMUX_GPIO158__FUNC_MSDC0_DAT4>,
<PINMUX_GPIO159__FUNC_MSDC0_DAT5>,
<PINMUX_GPIO160__FUNC_MSDC0_DAT6>,
<PINMUX_GPIO161__FUNC_MSDC0_DAT7>,
<PINMUX_GPIO162__FUNC_MSDC0_CMD>;
input-enable;
drive-strength = <6>;
bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
};
pins-clk {
pinmux = <PINMUX_GPIO163__FUNC_MSDC0_CLK>;
drive-strength = <6>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
};
pins-rst {
pinmux = <PINMUX_GPIO165__FUNC_MSDC0_RSTB>;
drive-strength = <6>;
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
};
pins-ds {
pinmux = <PINMUX_GPIO164__FUNC_MSDC0_DSL>;
drive-strength = <6>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
};
};
nfc_pins: nfc-pins {
pins-irq {
pinmux = <PINMUX_GPIO3__FUNC_GPIO3>;
bias-pull-down;
input-enable;
};
pins-fw-ven {
pinmux = <PINMUX_GPIO94__FUNC_GPIO94>,
<PINMUX_GPIO149__FUNC_GPIO149>;
};
};
ts_pins: touchscreen-pins {
pins-irq {
pinmux = <PINMUX_GPIO6__FUNC_GPIO6>;
bias-pull-up;
input-enable;
};
pins-rst {
pinmux = <PINMUX_GPIO102__FUNC_GPIO102>;
output-high;
};
};
proximity_pins: proximity-pins {
pins-irq {
pinmux = <PINMUX_GPIO8__FUNC_GPIO8>;
bias-pull-up;
input-enable;
};
};
accel_pins: accelerometer-pins {
pins-irq {
pinmux = <PINMUX_GPIO12__FUNC_GPIO12>;
bias-pull-up;
input-enable;
};
};
i2c0_pins: i2c0-pins {
pins-bus {
pinmux = <PINMUX_GPIO45__FUNC_SDA0>,
<PINMUX_GPIO46__FUNC_SCL0>;
input-enable;
};
};
i2c1_pins: i2c1-pins {
pins-bus {
pinmux = <PINMUX_GPIO125__FUNC_SDA1>,
<PINMUX_GPIO126__FUNC_SCL1>;
bias-disable;
};
};
i2c2_pins: i2c2-pins {
pins-bus {
pinmux = <PINMUX_GPIO43__FUNC_SDA2>,
<PINMUX_GPIO44__FUNC_SCL2>;
bias-disable;
};
};
i2c3_pins: i2c3-pins {
pins-bus {
pinmux = <PINMUX_GPIO136__FUNC_SDA3>,
<PINMUX_GPIO137__FUNC_SCL3>;
bias-disable;
};
};
i2c4_pins: i2c4-pins {
pins-bus {
pinmux = <PINMUX_GPIO100__FUNC_SDA4>,
<PINMUX_GPIO101__FUNC_SCL4>;
bias-disable;
};
};
uart0_pins: uart0-pins {
pins-rx {
pinmux = <PINMUX_GPIO113__FUNC_URXD0>;
bias-pull-up;
input-enable;
};
pins-tx {
pinmux = <PINMUX_GPIO114__FUNC_UTXD0>;
output-high;
};
};
uart2_pins: uart2-pins {
pins-rx {
pinmux = <PINMUX_GPIO31__FUNC_URXD2>;
bias-pull-up;
input-enable;
};
pins-tx {
pinmux = <PINMUX_GPIO32__FUNC_UTXD2>;
};
};
};
&pmic {
/*
* Smartphones, including the Xperia M5, are equipped with a companion
* MT6332 PMIC: when this is present, the main MT6331 PMIC will fire
* an interrupt on the companion, so we use the MT6332 IRQ GPIO.
*/
interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
mt6332-led {
compatible = "mediatek,mt6332-led";
#address-cells = <1>;
#size-cells = <0>;
pmic_bl_led: led@0 {
reg = <0>;
label = "backlight-pmic";
};
};
};
&pwm0 {
status = "okay";
};
&uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
};
&uart2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
};
