Anforderungen  |   Konzepte  |   Entwurf  |   Entwicklung  |   Qualitätssicherung  |   Lebenszyklus  |   Steuerung
 
 
 
 

products/Sources/formale Sprachen/C/Linux/arch/arm/boot/dts/st/   (Open Source Betriebssystem Version 6.17.9©)  Datei vom 24.10.2025 mit Größe 475 B image not shown  

Bilddatei

stm32mp157c-odyssey.dts


products/Sources/formale Sprachen/C/Linux/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts

// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) /* * Copyright (C) 2020 Marcin Sloniewski . */ /dts-v1/; #include "stm32mp157c-odyssey-som.dtsi" / { model = "Seeed Studio Odyssey-STM32MP157C Board"; compatible = "seeed,stm32mp157c-odyssey", "seeed,stm32mp157c-odyssey-som", "st,stm32mp157"; aliases { ethernet0 = ðernet0; serial0 = &uart4; }; chosen { stdout-path = "serial0:115200n8"; }; }; &dcmi { pinctrl-names = "default", "sleep"; pinctrl-0 = <&dcmi_pins_b>; pinctrl-1 = <&dcmi_sleep_pins_b>; }; ðernet0 { status = "okay"; pinctrl-0 = <ðernet0_rgmii_pins_a>; pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; pinctrl-names = "default", "sleep"; phy-mode = "rgmii-id"; max-speed = <1000>; phy-handle = <&phy0>; assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>; assigned-clock-parents = <&rcc PLL4_P>; assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */ st,eth-clk-sel; mdio { #address-cells = <1>; #size-cells = <0>; compatible = "snps,dwmac-mdio"; phy0: ethernet-phy@7 { /* KSZ9031RN */ reg = <7>; reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */ reset-assert-us = <10000>; reset-deassert-us = <300>; }; }; }; &i2c1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_pins_a>; pinctrl-1 = <&i2c1_sleep_pins_a>; i2c-scl-rising-time-ns = <100>; i2c-scl-falling-time-ns = <7>; status = "okay"; /delete-property/dmas; /delete-property/dma-names; }; &sdmmc1 { pinctrl-names = "default", "opendrain", "sleep"; pinctrl-0 = <&sdmmc1_b4_pins_a>; pinctrl-1 = <&sdmmc1_b4_od_pins_a>; pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; disable-wp; st,neg-edge; bus-width = <4>; vmmc-supply = <&v3v3>; status = "okay"; }; &uart4 { pinctrl-names = "default"; pinctrl-0 = <&uart4_pins_a>; /delete-property/dmas; /delete-property/dma-names; status = "okay"; };

                                                                                                                                                                                                                                                                                                                                                                                                     

Neuigkeiten

     Aktuelles
     Motto des Tages

Software

     Produkte
     Quellcodebibliothek

Aktivitäten

     Artikel über Sicherheit
     Anleitung zur Aktivierung von SSL

Muße

     Gedichte
     Musik
     Bilder
Jenseits des Üblichen ....
    

Besucherstatistik

Besucherstatistik

Monitoring

Montastic status badge