Quelle  s5pv210-aries.dtsi   Sprache: unbekannt

// SPDX-License-Identifier: GPL-2.0
/*
 * Samsung's S5PV210 based Galaxy Aries board device tree source
 */

/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "s5pv210.dtsi"

/ {
 compatible = "samsung,aries", "samsung,s5pv210";

 aliases: aliases {
  i2c4 = &i2c_sound;
  i2c5 = &i2c_accel;
  i2c6 = &i2c_pmic;
  i2c7 = &i2c_musb;
  i2c9 = &i2c_fuel;
  i2c10 = &i2c_touchkey;
  i2c11 = &i2c_prox;
  i2c12 = &i2c_magnetometer;
 };

 memory@30000000 {
  device_type = "memory";
  reg = <0x30000000 0x05000000>,
   <0x40000000 0x10000000>,
   <0x50000000 0x08000000>;
 };

 reserved-memory {
  #address-cells = <1>;
  #size-cells = <1>;
  ranges;

  mfc_left: region@43000000 {
   compatible = "shared-dma-pool";
   no-map;
   reg = <0x43000000 0x2000000>;
  };

  mfc_right: region@51000000 {
   compatible = "shared-dma-pool";
   no-map;
   reg = <0x51000000 0x2000000>;
  };
 };

 pmic_ap_clk: clock-0 {
  /* Workaround for missing clock on PMIC */
  compatible = "fixed-clock";
  #clock-cells = <0>;
  clock-frequency = <32768>;
 };

 bt_codec: bt-sco {
  compatible = "linux,bt-sco";
  #sound-dai-cells = <0>;
 };

 vibrator_pwr: regulator-fixed-0 {
  compatible = "regulator-fixed";
  regulator-name = "vibrator-en";
  enable-active-high;
  gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;

  pinctrl-names = "default";
  pinctrl-0 = <&vibrator_ena>;
 };

 touchkey_vdd: regulator-fixed-1 {
  compatible = "regulator-fixed";
  regulator-name = "VTOUCH_3.3V";
  regulator-min-microvolt = <3300000>;
  regulator-max-microvolt = <3300000>;
  enable-active-high;
  gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;

  pinctrl-names = "default";
  pinctrl-0 = <&touchkey_vdd_ena>;
 };

 gp2a_vled: regulator-fixed-2 {
  compatible = "regulator-fixed";
  regulator-name = "VLED";
  enable-active-high;
  gpio = <&gpj1 4 GPIO_ACTIVE_HIGH>;
  regulator-min-microvolt = <2800000>;
  regulator-max-microvolt = <2800000>;

  pinctrl-names = "default";
  pinctrl-0 = <&gp2a_power>;
 };

 wifi_pwrseq: wifi-pwrseq {
  compatible = "mmc-pwrseq-simple";
  reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
  pinctrl-names = "default";
  pinctrl-0 = <&wlan_gpio_rst>;
  post-power-on-delay-ms = <500>;
  power-off-delay-us = <500>;
 };

 i2c_sound: i2c-3 {
  compatible = "i2c-gpio";
  sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&sound_i2c_pins>;

  wm8994: audio-codec@1a {
   compatible = "wlf,wm8994";
   reg = <0x1a>;

   #sound-dai-cells = <0>;

   gpio-controller;
   #gpio-cells = <2>;

   clocks = <&clocks MOUT_CLKOUT>;
   clock-names = "MCLK1";

   AVDD2-supply = <&buck3_reg>;
   DBVDD-supply = <&buck3_reg>;
   CPVDD-supply = <&buck3_reg>;
   SPKVDD1-supply = <&buck3_reg>;
   SPKVDD2-supply = <&buck3_reg>;

   wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100
     0xa101 0x0100 0x8100 0x0100 0x0100
     0x0100>;

   wlf,ldo1ena-gpios = <&gpf3 4 GPIO_ACTIVE_HIGH>;
   wlf,ldo2ena-gpios = <&gpf3 4 GPIO_ACTIVE_HIGH>;

   wlf,lineout1-se;
   wlf,lineout2-se;

   assigned-clocks = <&clocks MOUT_CLKOUT>;
   assigned-clock-rates = <0>;
   assigned-clock-parents = <&xusbxti>;

   pinctrl-names = "default";
   pinctrl-0 = <&codec_ldo>;
  };
 };

 i2c_accel: i2c-4 {
  compatible = "i2c-gpio";
  sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&accel_i2c_pins>;

  accelerometer@38 {
   compatible = "bosch,bma023";
   reg = <0x38>;

   vdd-supply = <&ldo9_reg>;
   vddio-supply = <&ldo9_reg>;
  };
 };

 i2c_pmic: i2c-5 {
  compatible = "i2c-gpio";
  sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&pmic_i2c_pins>;

  pmic@66 {
   compatible = "maxim,max8998";
   reg = <0x66>;
   interrupt-parent = <&gph0>;
   interrupts = <7 IRQ_TYPE_EDGE_FALLING>;

   max8998,pmic-buck1-default-dvs-idx = <1>;
   max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
       <&gph0 4 GPIO_ACTIVE_HIGH>;
   max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
       <1050000>, <950000>;

   max8998,pmic-buck2-default-dvs-idx = <0>;
   max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
   max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;

   pinctrl-names = "default";
   pinctrl-0 = <&pmic_dvs_pins &pmic_irq>;

   regulators {
    ldo2_reg: LDO2 {
     regulator-name = "VALIVE_1.2V";
     regulator-min-microvolt = <1200000>;
     regulator-max-microvolt = <1200000>;
     regulator-always-on;

     regulator-state-mem {
      regulator-on-in-suspend;
     };
    };

    ldo3_reg: LDO3 {
     regulator-name = "VUSB_1.1V";
     regulator-min-microvolt = <1100000>;
     regulator-max-microvolt = <1100000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo4_reg: LDO4 {
     regulator-name = "VADC_3.3V";
     regulator-min-microvolt = <3300000>;
     regulator-max-microvolt = <3300000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo5_reg: LDO5 {
     regulator-name = "VTF_2.8V";
     regulator-min-microvolt = <2800000>;
     regulator-max-microvolt = <2800000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo6_reg: LDO6 {
     regulator-name = "LDO6";
     regulator-min-microvolt = <1600000>;
     regulator-max-microvolt = <3600000>;
    };

    ldo7_reg: LDO7 {
     regulator-name = "VLCD_1.8V";
     regulator-min-microvolt = <1800000>;
     regulator-max-microvolt = <1800000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo8_reg: LDO8 {
     regulator-name = "VUSB_3.3V";
     regulator-min-microvolt = <3300000>;
     regulator-max-microvolt = <3300000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo9_reg: LDO9 {
     regulator-name = "VCC_2.8V_PDA";
     regulator-min-microvolt = <2800000>;
     regulator-max-microvolt = <2800000>;
     regulator-always-on;
    };

    ldo10_reg: LDO10 {
     regulator-name = "VPLL_1.2V";
     regulator-min-microvolt = <1200000>;
     regulator-max-microvolt = <1200000>;
     regulator-always-on;

     regulator-state-mem {
      regulator-on-in-suspend;
     };
    };

    ldo11_reg: LDO11 {
     regulator-name = "CAM_AF_3.0V";
     regulator-min-microvolt = <3000000>;
     regulator-max-microvolt = <3000000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo12_reg: LDO12 {
     regulator-name = "CAM_SENSOR_CORE_1.2V";
     regulator-min-microvolt = <1200000>;
     regulator-max-microvolt = <1200000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo13_reg: LDO13 {
     regulator-name = "VGA_VDDIO_2.8V";
     regulator-min-microvolt = <2800000>;
     regulator-max-microvolt = <2800000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo14_reg: LDO14 {
     regulator-name = "VGA_DVDD_1.8V";
     regulator-min-microvolt = <1800000>;
     regulator-max-microvolt = <1800000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo15_reg: LDO15 {
     regulator-name = "CAM_ISP_HOST_2.8V";
     regulator-min-microvolt = <2800000>;
     regulator-max-microvolt = <2800000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo16_reg: LDO16 {
     regulator-name = "VGA_AVDD_2.8V";
     regulator-min-microvolt = <2800000>;
     regulator-max-microvolt = <2800000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ldo17_reg: LDO17 {
     regulator-name = "VCC_3.0V_LCD";
     regulator-min-microvolt = <3000000>;
     regulator-max-microvolt = <3000000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    buck1_reg: BUCK1 {
     regulator-name = "vddarm";
     regulator-min-microvolt = <750000>;
     regulator-max-microvolt = <1500000>;

     regulator-state-mem {
      regulator-off-in-suspend;
      regulator-suspend-microvolt = <1250000>;
     };
    };

    buck2_reg: BUCK2 {
     regulator-name = "vddint";
     regulator-min-microvolt = <750000>;
     regulator-max-microvolt = <1500000>;

     regulator-state-mem {
      regulator-off-in-suspend;
      regulator-suspend-microvolt = <1100000>;
     };
    };

    buck3_reg: BUCK3 {
     regulator-name = "VCC_1.8V";
     regulator-min-microvolt = <1800000>;
     regulator-max-microvolt = <1800000>;
     regulator-always-on;
    };

    buck4_reg: BUCK4 {
     regulator-name = "CAM_ISP_CORE_1.2V";
     regulator-min-microvolt = <1200000>;
     regulator-max-microvolt = <1200000>;

     regulator-state-mem {
      regulator-off-in-suspend;
     };
    };

    ap32khz_reg: EN32KHz-AP {
     regulator-name = "32KHz AP";
     regulator-always-on;
    };

    cp32khz_reg: EN32KHz-CP {
     regulator-name = "32KHz CP";
    };

    vichg_reg: ENVICHG {
     regulator-name = "VICHG";
     regulator-always-on;
    };

    safe1_sreg: ESAFEOUT1 {
     regulator-name = "SAFEOUT1";
    };

    safe2_sreg: ESAFEOUT2 {
     regulator-name = "SAFEOUT2";
    };
   };
  };
 };

 i2c_musb: i2c-6 {
  compatible = "i2c-gpio";
  sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&musb_i2c_pins>;

  fsa9480: musb@25 {
   compatible = "fcs,fsa9480";
   reg = <0x25>;
   interrupt-parent = <&gph2>;
   interrupts = <7 IRQ_TYPE_EDGE_FALLING>;

   pinctrl-names = "default";
   pinctrl-0 = <&musb_irq>;
  };
 };

 i2c_fuel: i2c-7 {
  compatible = "i2c-gpio";
  sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&fg_i2c_pins>;

  fg: fuelgauge@36 {
   compatible = "maxim,max17040";
   reg = <0x36>;
  };
 };

 i2c_touchkey: i2c-8 {
  compatible = "i2c-gpio";
  sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&touchkey_i2c_pins>;

  touchkey@20 {
   compatible = "cypress,aries-touchkey";
   reg = <0x20>;
   vdd-supply = <&touchkey_vdd>;
   vcc-supply = <&buck3_reg>;
   linux,keycodes = <KEY_MENU KEY_BACK
       KEY_HOMEPAGE KEY_SEARCH>;
   interrupt-parent = <&gpj4>;
   interrupts = <1 IRQ_TYPE_LEVEL_LOW>;

   pinctrl-names = "default";
   pinctrl-0 = <&touchkey_irq>;
  };
 };

 i2c_prox: i2c-9 {
  compatible = "i2c-gpio";
  sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&prox_i2c_pins>;

  light-sensor@44 {
   compatible = "sharp,gp2ap002a00f";
   reg = <0x44>;
   interrupt-parent = <&gph0>;
   interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
   vdd-supply = <&gp2a_vled>;
   vio-supply = <&gp2a_vled>;
   io-channels = <&gp2a_shunt>;
   io-channel-names = "alsout";
   sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
   sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;

   pinctrl-names = "default";
   pinctrl-0 = <&gp2a_irq>;
  };
 };

 i2c_magnetometer: i2c-10 {
  compatible = "i2c-gpio";
  sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  i2c-gpio,delay-us = <2>;
  #address-cells = <1>;
  #size-cells = <0>;

  pinctrl-names = "default";
  pinctrl-0 = <&magnetometer_i2c_pins>;

  status = "disabled";

  /* Yamaha yas529 magnetometer, no mainline binding */
 };

 vibrator: pwm-vibrator {
  compatible = "pwm-vibrator";
  pwms = <&pwm 1 44642 0>;
  pwm-names = "enable";
  vcc-supply = <&vibrator_pwr>;
  pinctrl-names = "default";
  pinctrl-0 = <&pwm1_out>;
 };

 poweroff: syscon-poweroff {
  compatible = "syscon-poweroff";
  regmap = <&pmu_syscon>;
  offset = <0x681c>; /* PS_HOLD_CONTROL */
  value = <0x5200>;
 };

 spi_lcd: spi-2 {
  compatible = "spi-gpio";
  #address-cells = <1>;
  #size-cells = <0>;

  sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>;
  mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>;
  cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>;
  num-chipselects = <1>;

  pinctrl-names = "default";
  pinctrl-0 = <&lcd_spi_pins>;

  panel@0 {
   compatible = "samsung,s6e63m0";
   reg = <0>;
   reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
   vdd3-supply = <&ldo7_reg>;
   vci-supply = <&ldo17_reg>;
   spi-max-frequency = <1200000>;

   pinctrl-names = "default";
   pinctrl-0 = <&panel_rst>;

   port {
    lcd_ep: endpoint {
     remote-endpoint = <&fimd_ep>;
    };
   };
  };
 };
};

&adc {
 vdd-supply = <&ldo4_reg>;

 status = "okay";

 gp2a_shunt: current-sense-shunt {
  compatible = "current-sense-shunt";
  io-channels = <&adc 9>;
  shunt-resistor-micro-ohms = <47000000>; /* 47 ohms */
  #io-channel-cells = <0>;
 };
};

&fimd {
 pinctrl-names = "default";
 pinctrl-0 = <&lcd_clk &lcd_data24>;
 status = "okay";

 samsung,invert-vden;
 samsung,invert-vclk;

 #address-cells = <1>;
 #size-cells = <0>;

 port@3 {
  reg = <3>;
  fimd_ep: endpoint {
   remote-endpoint = <&lcd_ep>;
  };
 };
};

&hsotg {
 vusb_a-supply = <&ldo8_reg>;
 vusb_d-supply = <&ldo3_reg>;
 dr_mode = "peripheral";
 status = "okay";
};

&i2c2 {
 samsung,i2c-sda-delay = <100>;
 samsung,i2c-max-bus-freq = <400000>;
 samsung,i2c-slave-addr = <0x10>;
 status = "okay";

 touchscreen@4a {
  compatible = "atmel,maxtouch";
  reg = <0x4a>;
  interrupt-parent = <&gpj0>;
  interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
  pinctrl-names = "default";
  pinctrl-0 = <&ts_irq>;
  reset-gpios = <&gpj1 3 GPIO_ACTIVE_LOW>;
 };
};

&i2s0 {
 dmas = <&pdma0 10>, <&pdma0 9>, <&pdma0 11>;
 status = "okay";
};

&mfc {
 memory-region = <&mfc_left>, <&mfc_right>;
};

&pinctrl0 {
 bt_reset: bt-reset-pins {
  samsung,pins = "gpb-3";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 wlan_bt_en: wlan-bt-en-pins {
  samsung,pins = "gpb-5";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-val = <1>;
 };

 codec_ldo: codec-ldo-pins {
  samsung,pins = "gpf3-4";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 };

 prox_i2c_pins: gp2a-i2c-pins {
  samsung,pins = "gpg0-2", "gpg2-2";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 wlan_gpio_rst: wlan-gpio-rst-pins {
  samsung,pins = "gpg1-2";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 };

 bt_wake: bt-wake-pins {
  samsung,pins = "gpg3-4";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 };

 gp2a_irq: gp2a-irq-pins {
  samsung,pins = "gph0-2";
  samsung,pin-function = <S5PV210_PIN_FUNC_F>;
  samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 pmic_dvs_pins: pmic-dvs-pins {
  samsung,pins = "gph0-3", "gph0-4", "gph0-5";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
  samsung,pin-val = <0>;
 };

 pmic_irq: pmic-irq-pins {
  samsung,pins = "gph0-7";
  samsung,pin-function = <S5PV210_PIN_FUNC_F>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 wifi_host_wake: wifi-host-wake-pins {
  samsung,pins = "gph2-4";
  samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 bt_host_wake: bt-host-wake-pins {
  samsung,pins = "gph2-5";
  samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 musb_irq: musq-irq-pins {
  samsung,pins = "gph2-7";
  samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 tf_detect: tf-detect-pins {
  samsung,pins = "gph3-4";
  samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 wifi_wake: wifi-wake-pins {
  samsung,pins = "gph3-5";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 };

 magnetometer_i2c_pins: yas529-i2c-pins {
  samsung,pins = "gpj0-0", "gpj0-1";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 ts_irq: ts-irq-pins {
  samsung,pins = "gpj0-5";
  samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 vibrator_ena: vibrator-ena-pins {
  samsung,pins = "gpj1-1";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 gp2a_power: gp2a-power-pins {
  samsung,pins = "gpj1-4";
  samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 touchkey_i2c_pins: touchkey-i2c-pins {
  samsung,pins = "gpj3-0", "gpj3-1";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 touchkey_vdd_ena: touchkey-vdd-ena-pins {
  samsung,pins = "gpj3-2";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 musb_i2c_pins: musb-i2c-pins {
  samsung,pins = "gpj3-4", "gpj3-5";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 accel_i2c_pins: accel-i2c-pins {
  samsung,pins = "gpj3-6", "gpj3-7";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 pmic_i2c_pins: pmic-i2c-pins {
  samsung,pins = "gpj4-0", "gpj4-3";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 touchkey_irq: touchkey-irq-pins {
  samsung,pins = "gpj4-1";
  samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
  samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 lcd_spi_pins: spi-lcd-pins {
  samsung,pins = "mp01-1", "mp04-1", "mp04-3";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 fg_i2c_pins: fg-i2c-pins {
  samsung,pins = "mp05-0", "mp05-1";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 sound_i2c_pins: sound-i2c-pins {
  samsung,pins = "mp05-2", "mp05-3";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };

 panel_rst: panel-rst-pins {
  samsung,pins = "mp05-5";
  samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
  samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 };
};

&pwm {
 samsung,pwm-outputs = <1>;
};

&rtc {
 clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
 clock-names = "rtc", "rtc_src";
};

&sdhci1 {
 #address-cells = <1>;
 #size-cells = <0>;

 bus-width = <4>;
 max-frequency = <38400000>;
 pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
 pinctrl-names = "default";
 cap-sd-highspeed;
 cap-mmc-highspeed;
 keep-power-in-suspend;

 mmc-pwrseq = <&wifi_pwrseq>;
 non-removable;
 status = "okay";

 assigned-clocks = <&clocks MOUT_MMC1>, <&clocks SCLK_MMC1>;
 assigned-clock-rates = <0>, <50000000>;
 assigned-clock-parents = <&clocks MOUT_MPLL>;

 wifi@1 {
  reg = <1>;
  compatible = "brcm,bcm4329-fmac";
  interrupt-parent = <&gph2>;
  interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
  interrupt-names = "host-wake";
 };
};

&sdhci2 {
 bus-width = <4>;
 cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>;
 vmmc-supply = <&ldo5_reg>;
 pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>;
 pinctrl-names = "default";
 status = "okay";

 assigned-clocks = <&clocks MOUT_MMC2>, <&clocks SCLK_MMC2>;
 assigned-clock-rates = <0>, <50000000>;
 assigned-clock-parents = <&clocks MOUT_MPLL>;
};

&uart0 {
 assigned-clocks = <&clocks MOUT_UART0>, <&clocks SCLK_UART0>;
 assigned-clock-rates = <0>, <111166667>;
 assigned-clock-parents = <&clocks MOUT_MPLL>;

 status = "okay";

 bluetooth {
  compatible = "brcm,bcm4329-bt";
  max-speed = <3000000>;
  pinctrl-names = "default";
  pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake
        &bt_reset &bt_wake>;
  shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>;
  device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
  interrupt-parent = <&gph2>;
  interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
  interrupt-names = "host-wakeup";
 };
};

&uart1 {
 status = "okay";
};

&uart2 {
 status = "okay";
};

&usbphy {
 status = "okay";
 vbus-supply = <&safe1_sreg>;
};

&xusbxti {
 clock-frequency = <24000000>;
};