// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH
*/
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Phytec phyFLEX-i.MX6 Quad";
compatible = "phytec,imx6q-pfla02", "fsl,imx6q";
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x80000000>;
};
reg_usb_otg_vbus: regulator-usb-otg-vbus {
compatible = "regulator-fixed";
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio4 15 0>;
enable-active-high;
};
reg_usb_h1_vbus: regulator-usb-h1-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1_vbus>;
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 0 0>;
enable-active-high;
};
gpio_leds: leds {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
compatible = "gpio-leds";
led_green: led-green {
label = "phyflex:green";
gpios = <&gpio1 30 0>;
};
led_red: led-red {
label = "phyflex:red";
gpios = <&gpio2 31 0>;
};
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "disabled";
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan1>;
status = "disabled";
};
&ecspi3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3>;
status = "okay";
cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
som_flash: flash@0 {
compatible = "m25p80", "jedec,spi-nor";
spi-max-frequency = <20000000>;
reg = <0>;
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-handle = <ðphy>;
phy-mode = "rgmii";
phy-reset-duration = <10>; /* in msecs */
phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
phy-supply = <&vdd_eth_io_reg>;
status = "disabled";
fec_mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
txc-skew-ps = <1680>;
rxc-skew-ps = <1860>;
};
};
};
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
nand-on-flash-bbt;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
som_eeprom: eeprom@50 {
compatible = "catalyst,24c32", "atmel,24c32";
pagesize = <32>;
reg = <0x50>;
};
pmic@58 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pmic>;
compatible = "dlg,da9063";
reg = <0x58>;
interrupt-parent = <&gpio2>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */
#interrupt-cells = <2>;
interrupt-controller;
regulators {
vddcore_reg: bcore1 {
regulator-min-microvolt = <730000>;
regulator-max-microvolt = <1380000>;
regulator-always-on;
};
vddsoc_reg: bcore2 {
regulator-min-microvolt = <730000>;
regulator-max-microvolt = <1380000>;
regulator-always-on;
};
vdd_ddr3_reg: bpro {
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
};
vdd_3v3_reg: bperi {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_buckmem_reg: bmem {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_eth_reg: bio {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vdd_eth_io_reg: ldo4 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-always-on;
};
vdd_mx6_snvs_reg: ldo5 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
vdd_3v3_pmic_io_reg: ldo6 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_sd0_reg: ldo9 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vdd_sd1_reg: ldo10 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vdd_mx6_high_reg: ldo11 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
};
da9063_rtc: rtc {
compatible = "dlg,da9063-rtc";
};
da9063_wdog: watchdog {
compatible = "dlg,da9063-watchdog";
};
onkey {
compatible = "dlg,da9063-onkey";
status = "disabled";
};
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
clock-frequency = <100000>;
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
clock-frequency = <100000>;
};
&iomuxc {
pinctrl_ecspi3: ecspi3grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* CS0 */
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 /* Reset GPIO */
>;
};
pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b0
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0
>;
};
pinctrl_gpmi_nand: gpminandgrp {
fsl,pins = <
MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* Green LED */
MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x80000000 /* Red LED */
>;
};
pinctrl_pcie: pciegrp {
fsl,pins = <MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x80000000>;
};
pinctrl_pmic: pmicgrp {
fsl,pins = <MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x80000000>; /* PMIC interrupt */
};
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_usbh1_vbus: usbh1vbusgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
>;
};
pinctrl_usdhc3_cdwp: usdhc3cdwpgrp {
fsl,pins = <
MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000
>;
};
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x130b0
MX6QDL_PAD_DISP0_DAT17__AUD5_TXD 0x110b0
MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x130b0
MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
>;
};
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
reset-gpio = <&gpio4 17 GPIO_ACTIVE_LOW>;
status = "disabled";
};
®_arm {
vin-supply = <&vddcore_reg>;
};
®_pu {
vin-supply = <&vddsoc_reg>;
};
®_soc {
vin-supply = <&vddsoc_reg>;
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
uart-has-rtscts;
status = "disabled";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "disabled";
};
&usbh1 {
vbus-supply = <®_usb_h1_vbus>;
status = "disabled";
};
&usbotg {
vbus-supply = <®_usb_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
status = "disabled";
};
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
vmmc-supply = <&vdd_sd1_reg>;
status = "disabled";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3
&pinctrl_usdhc3_cdwp>;
cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
vmmc-supply = <&vdd_sd0_reg>;
status = "disabled";
};
&wdog1 {
/*
* Rely on PMIC reboot handler. Internal i.MX6 watchdog, that is also
* used for reboot, does not reset all external PMIC voltages on reset.
*/
status = "disabled";
};
[ Dauer der Verarbeitung: 0.3 Sekunden
(vorverarbeitet)
]
