Eine aufbereitete Darstellung der Quelle

 
     
 
 
Anforderungen  |   Konzepte  |   Entwurf  |   Entwicklung  |   Qualitätssicherung  |   Lebenszyklus  |   Steuerung
 
 
 
 
Benutzer

products/Sources/formale Sprachen/C/LibreOffice/icon-themes/breeze_svg/cmd/32/   (LibreOffice Version 25.8.3.2©)  Datei vom 5.10.2025 mit Größe 380 B image not shown  

Bilddatei

logicpd-torpedo-37xx-devkit.dts


products/Sources/formale Sprachen/C/Linux/arch/arm/boot/dts/ti/omap/logicpd-torpedo-37xx-devkit.dts

// SPDX-License-Identifier: GPL-2.0-only /dts-v1/; #include "omap36xx.dtsi" #include "logicpd-torpedo-som.dtsi" #include "omap-gpmc-smsc9221.dtsi" #include "logicpd-torpedo-baseboard.dtsi" / { model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; wl12xx_vmmc: wl12xx_vmmc { compatible = "regulator-fixed"; regulator-name = "vwl1271"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; gpio = <&gpio5 29 0>; /* gpio157 */ startup-delay-us = <70000>; enable-active-high; vin-supply = <&vmmc2>; }; }; /* * Only found on the wireless SOM. For the SOM without wireless, the pins for * MMC3 can be routed with jumpers to the second MMC slot on the devkit and * gpio157 is not connected. So this should be OK to keep common for now, * probably device tree overlays is the way to go with the various SOM and * jumpering combinations for the long run. */ &mmc3 { interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>; pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; pinctrl-names = "default"; vmmc-supply = <&wl12xx_vmmc>; non-removable; bus-width = <4>; cap-power-off-card; #address-cells = <1>; #size-cells = <0>; wlcore: wlcore@2 { compatible = "ti,wl1283"; reg = <2>; interrupt-parent = <&gpio5>; interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */ ref-clock-frequency = <26000000>; tcxo-clock-frequency = <26000000>; }; }; &uart2 { /delete-property/dma-names; bluetooth-gnss { compatible = "ti,wl1283-st"; enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */ max-speed = <3000000>; }; }; /* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */ &mt9p031_out { pixel-clock-frequency = <90000000>; }; &omap3_pmx_core { mmc3_pins: mm3-pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ >; }; }; &omap3_pmx_core2 { mmc3_core2_pins: mmc3-core2-pins { pinctrl-single,pins = < OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ >; }; }; /* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */ &omap3_pmx_wkup { isp1763_pins: isp1763-pins { pinctrl-single,pins = < OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_128 */ >; }; };

                                                                                                                                                                                                                                                                                                                                                                                                     

Neuigkeiten

     Aktuelles
     Motto des Tages

Open Source Software

     Quellcodebibliothek
     Eigene Quellcodes
     Fremde Quellcodes
     Suchen
Jenseits des Üblichen ....

Besucherstatistik

Besucherstatistik
Statistik
#Sources=1126864
#Domains=2039723